P0014 on Honda
Exhaust Camshaft Position Timing - Over-Advanced (Bank 1)
P0014 on Honda vehicles indicates exhaust camshaft position timing - over-advanced (bank 1). Au7o has documented this code across 4 Honda models — most commonly on Civic, CR-V, Element. P0014 means the exhaust camshaft on bank 1 is timed too far advanced — the variable valve timing (VVT) system has moved the cam beyond the position the computer commanded, or it's stuck in an over-advanced position. The engine uses VVT to rotate the camshaft and optimize valve timing for power, economy, and emissions; the computer compares the commanded cam position to the actual reading from the cam sensor and flags this code when they don't agree. Common results are rough idle, reduced power, poor fuel economy, or a rattle at start-up. Oil flow and the VVT actuator are the usual suspects. Typical repair costs on Honda range from $300 to $2,500, depending on the specific model and root cause.
Common Causes of P0014
- •Low or dirty engine oil restricting VVT operation
- •Stuck or failed camshaft oil control valve (VVT solenoid)
- •Clogged VVT solenoid screen or oil passages
- •Faulty camshaft phaser/actuator
- •Wiring or connector fault at the oil control valve
- •Stretched timing chain or jumped timing
- •Camshaft position sensor fault giving incorrect reading
P0014 on Honda by Model
Honda Civic(1 issue)
- Timing Chain VTC Actuator Rattle on Cold Start (8th Gen)2006-2011
The 8th generation Civic (2006-2011) equipped with the R18A and K20Z3 engines suffers from Variable Timing Control (VTC) actuator failure causing a loud metallic rattling noise on cold startup that typically lasts 1-5 seconds before oil pressure builds. The actuator locks the cam timing and rattles when the internal ratchet mechanism wears. This is the same issue that plagued the 2006-2011 CR-V. Honda issued TSB 07-010 addressing the noise but stopped short of a recall. Continued driving with a failed VTC actuator can damage the timing chain and guides, leading to catastrophic engine failure.
Honda CR-V(2 issues)
- VTC Actuator Failure - Cold Start Rattle2012-2016
The Variable Timing Control (VTC) actuator fails, causing a loud rattling or grinding noise for 1-2 seconds during cold engine startup. The issue is caused by the actuator's internal lock pin not engaging properly. If left unaddressed, this can lead to timing chain wear and potential engine damage.
- K24 Timing Chain Tensioner Failure - VTC Actuator Rattle (3rd Gen)2007-2011
The K24Z2 2.4L engine in the 3rd generation CR-V shares the same Variable Timing Control (VTC) actuator design flaw as the 2006-2011 Civic. The VTC actuator develops internal ratchet mechanism wear causing a loud metallic rattle on cold starts that lasts 1-5 seconds. The hydraulic timing chain tensioner also weakens over time, allowing chain slack. Honda issued TSB 07-010 addressing VTC actuator noise with improved actuator design. Ignored VTC rattles lead to timing chain elongation and guide wear, which can cause catastrophic engine failure on very high-mileage vehicles.
Honda Element(1 issue)
- Timing Chain Rattle on Cold Start (K24A)2003-2011
K24A engine timing chain tensioner wear causes rattling noise on cold start. Many Elements reach 200k+ miles without chain issues - don't replace unless confirmed diagnosis per Element community consensus. If persistent rattling: Replace timing chain, tensioner, guides, and VTC oil control solenoid together (complete kit, not individual parts). Honda TSB 09-10 references VTC actuator issues. Use OEM Honda parts for timing components.
Honda Odyssey(1 issue)
- Critical Timing Belt and Water Pump Service2005-2010
3.5L V6 engine uses interference design with timing belt (not chain). If timing belt breaks, valves collide with pistons causing catastrophic engine damage ($5,000-$8,000). Honda recommends timing belt replacement at 7 years or 105,000 miles. Water pump is driven by timing belt, making simultaneous replacement cost-effective. 2011+ Odysseys use timing chain (no replacement needed).
Looking for P0014 on a different make?
View P0014 across all makes →Frequently Asked Questions
What does P0014 mean on Honda?▼
P0014 stands for "Exhaust Camshaft Position Timing - Over-Advanced (Bank 1)." P0014 means the exhaust camshaft on bank 1 is timed too far advanced — the variable valve timing (VVT) system has moved the cam beyond the position the computer commanded, or it's stuck in an over-advanced position. The engine uses VVT to rotate the camshaft and optimize valve timing for power, economy, and emissions; the computer compares the commanded cam position to the actual reading from the cam sensor and flags this code when they don't agree. Common results are rough idle, reduced power, poor fuel economy, or a rattle at start-up. Oil flow and the VVT actuator are the usual suspects. On Honda specifically, this code is documented across 4 models.
What causes P0014 on Honda vehicles?▼
Common causes on Honda: Low or dirty engine oil restricting VVT operation, Stuck or failed camshaft oil control valve (VVT solenoid), Clogged VVT solenoid screen or oil passages, Faulty camshaft phaser/actuator, Wiring or connector fault at the oil control valve. Specific causes vary by model and year — see the per-model sections below.
How much does it cost to fix P0014 on a Honda?▼
Repair costs on Honda range from $300 to $2,500, depending on the specific model and root cause.
Which Honda models have P0014 documented?▼
Au7o has documented P0014 on 4 Honda models: Civic, CR-V, Element, Odyssey.