According to Au7o's research across NHTSA recalls, manufacturer TSBs, and owner forum reports, the 1994 Lexus GS300 has 2 documented known issues, with 1 rated critical. The most serious is 2JZ-GE Timing Belt Service - Interval Confusion and Interference Engine Risk ($700-$1,500 repair). Across all issues, repair costs range from $200 to $1,500. DIY maintenance guides at au7o.io.
On the 1993-1997 Lexus GS300 2JZ-GE 3.0L I6, the 2JZ-GE inline-six in the 1993-1997 GS300 (JZS147) uses a rubber timing belt with Lexus's factory replacement interval set at 90,000 miles, while the same engine in the Toyota Supra is specified at 110,000 miles - causing widespread owner confusion about the correct service interval. Although the 2JZ-GE is often described as 'non-interference,' multiple sources and shop reports document bent valves when the belt fails, jumps a tooth, or is installed with incorrect timing. Service requires removing the radiator, fan shroud, crank pulley, and timing covers, and most independents replace the water pump, idler/tensioner pulleys, cam/crank seals, and accessory belts at the same time. Aged hydraulic tensioners and oil-soaked belts from leaking front cam seals are commonly found during the job.
Common Symptoms
Squealing or chirping from front of engine
Visible cracks, glazing, or missing teeth on timing belt
Engine cranks but will not start after belt jumps or breaks
Oil contamination of timing belt from front cam/crank seal leak
Rough running or no compression after belt failure (bent valves)
How to Fix
Replace the timing belt at 90,000 miles per Lexus factory schedule (do not stretch to Supra's 110k interval on a Lexus chassis). Replace the hydraulic tensioner, idler pulley, water pump, thermostat, drive belts, and front cam/crank seals at the same time - labor to access these parts is the bulk of the job. Use OEM Aisin or Toyota/Mitsuboshi belt. Verify cam and crank timing marks at TDC #1 before reinstalling covers, and rotate the engine two full revolutions by hand to confirm no valve-to-piston contact before cranking with the starter.
Medium ConfidenceVerified0 reportsLast reported by owners Invalid DateReviewed Jun 2026
On the 1993-1997 Lexus GS300 2JZ-GE 3.0L I6, the 1993-1997 GS300 (JZS147) front suspension uses double-wishbone geometry with soft factory rubber bushings in the lower control arms. These bushings crack, separate from the inner sleeve, and rot out as they age, allowing the control arm to walk under braking and acceleration. The result is a hollow 'clunk' or banging from the front end over bumps, wandering steering, uneven inner-edge tire wear, and an inability to hold an alignment. Lexus does not sell the bushing separately at the dealer - the OEM service is to replace the entire control arm assembly, which is expensive. Aftermarket press-in bushing kits (rubber or polyurethane from SuperPro, Whiteline, Prothane) are the cost-effective fix for this generation.
Common Symptoms
Clunking or banging from front end over bumps
Vague or wandering steering on-center
Pulling under braking
Inner-edge tire wear
Cannot hold a front alignment after adjustment
How to Fix
Inspect the lower control arm bushings with a pry bar - any visible cracking, separation between the rubber and inner sleeve, or excessive deflection means replace. Remove the lower control arm (disconnect ball joint, sway-bar end link, and the two pivot bolts). Press out the worn bushings and press in OEM-rubber or polyurethane replacements (SuperPro SPF3163K is sized specifically for the 1993-1997 GS300). Reinstall, torque pivot bolts to spec with the suspension loaded at ride height (to avoid pre-loading the new bushings), and perform a four-wheel alignment.
Low ConfidenceVerified0 reportsLast reported by owners Invalid DateReviewed Jun 2026
⚠️NHTSA Recalls2 recalls
SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT
VEHICLE DESCRIPTION: PASSENGER VEHICLES. DUE TO INADEQUATE LUBRICATION OF THE INSIDE OF THE LOWER BALL JOINTS, EXCESSIVE WEAR CAN OCCUR CAUSING DAMAGE TO THE LOWER BALL JOINTS. SEPARATION OF THE LOWER BALL JOINTS FROM THE STEERING KNUCKLE ARMS COULD OCCUR.
Campaign #99V12500019/05/1999
SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT
THE SPHERICAL PORTIONS OF CERTAIN LOWER BALL JOINTS HAD FINISHED SURFACES THAT WERE NOT SMOOTH CAUSING FRICTION WITH THE SURFACE OF THE BALL JOINT CAP.
Campaign #95V07200003/04/1995
Enter your VIN at NHTSA.gov to check recalls specific to your vehicle.
According to Au7o's research across NHTSA recalls, manufacturer TSBs, and owner forum reports, the 1994-1994 Lexus GS300 has 2 documented issues. The most frequently reported are: 2JZ-GE Timing Belt Service - Interval Confusion and Interference Engine Risk, Front Lower Control Arm Bushing Failure. Of these, 1 is rated critical and should be addressed promptly.
Is the Lexus GS300 reliable?
The 1994-1994 Lexus GS300 has 2 known issues compiled from NHTSA recalls, manufacturer TSBs, and owner forum reports. 1 issue is rated critical: 2JZ-GE Timing Belt Service - Interval Confusion and Interference Engine Risk. Prospective buyers should inspect for these issues and factor potential repair costs into their purchase decision. Regular maintenance following the manufacturer's schedule helps prevent many common problems.
How much does it cost to fix common Lexus GS300 problems?
Repair costs for known Lexus GS300 issues range from $200 to $1,500, depending on the specific problem and whether you choose DIY or professional repair. The most critical issue, 2JZ-GE Timing Belt Service - Interval Confusion and Interference Engine Risk, typically costs $700-$1,500 to repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.
What is the 1993-1997 Lexus GS300 2JZ-GE Timing Belt Service - Interval Confusion and Interference Engine Risk?
The 2JZ-GE inline-six in the 1993-1997 GS300 (JZS147) uses a rubber timing belt with Lexus's factory replacement interval set at 90,000 miles, while the same engine in the Toyota Supra is specified at 110,000 miles - causing widespread owner confusion about the correct service in… Repairs typically run $700-$1,500. Severity: high.
What is the 1993-1997 Lexus GS300 Front Lower Control Arm Bushing Failure?
The 1993-1997 GS300 (JZS147) front suspension uses double-wishbone geometry with soft factory rubber bushings in the lower control arms. These bushings crack, separate from the inner sleeve, and rot out as they age, allowing the control arm to walk under braking and acceleration. Repairs typically run $200-$900. Severity: medium.
Content on this page was compiled with AI assistance using NHTSA complaints, TSBs, owner reports, and public automotive data. While we strive for accuracy, this information may contain errors. Always verify repair procedures and specifications with your vehicle's service manual or a qualified mechanic.
