2007 BMW M6 Problems: 4 Issues Every Owner Should Know

2007 model year · 0+ owner reports · Updated April 2026

According to Au7o's analysis of 0+ owner reports, the 2007 BMW M6 has 4 documented known issues, with 3 rated critical. The most serious are SMG Hydraulic Pump and Clutch Actuator Failure ($2,000-$4,000 repair), Rod Bearing Premature Wear (S65/S63 Engines) ($3,000-$6,000 repair) and S85 V10 Rod Bearing Failure (Catastrophic Engine Destruction) ($6,500-$32,000 repair). Across all issues, repair costs range from $500 to $32,000. DIY maintenance guides at au7o.io.

All 4 Known Issues

Filter:

When Issues Typically Appear

S85 V10 Throttle Actuator Failure (Plastic Gear Stripping)

56K-84K

Rod Bearing Premature Wear (S65/S63 Engines)

60K-80K

S85 V10 Rod Bearing Failure (Catastrophic Engine Destruction)

60K-100K

SMG Hydraulic Pump and Clutch Actuator Failure

72K-108K

038K75K113K150K mi

On the 2005-2019 BMW M6, both the S65 V8 (E63 M6) and S63 twin-turbo V8 (F06/F12/F13 M6) suffer from premature rod bearing wear. The S65 is particularly notorious — the OEM rod bearings use a copper-lead composition that wears rapidly, especially with frequent cold starts and short trips. The S63 has improved bearings but can still experience wear at higher mileages. Failure to catch worn bearings leads to spun bearings and catastrophic engine failure.

This issue also affects: BMW 7 Series, BMW M3, BMW M5

Common Symptoms

Metallic ticking or knocking from engine at idle
Copper or bronze particles visible in oil filter
Oil analysis showing elevated copper and lead levels
Roughness felt through drivetrain at low RPM
Engine knock under load

How to Fix

Perform a preventive rod bearing replacement between 60,000-80,000 miles on S65 engines, and inspect by 80,000-100,000 miles on S63 engines. Use upgraded ACL or King XP bearings with coated surfaces. Cut and send used oil filter for analysis — bearing material particles indicate wear progression. The job requires engine-out on the S65 (approximately 20 hours labor) or can be done in-car on the S63 with the oil pan dropped.

What Owners Are Using

Parts and tips from 0+ owners who fixed this issue

Tip
UpgradePerformance engine bearing set for reliable bottom-end protection (ACL Engine Bearing Set)
View on Amazon
UpgradeAssembly lube protects bearings during initial startup after rebuild (Permatex Engine Assembly Lube)
View on Amazon

Typical repair cost:$3,000 - $6,000

Research This Issue

0+ owners have reported this issue

Google Reddit YouTube NHTSA

Community Reported

High Confidence0 reportsLast reported by owners Invalid DateReviewed Invalid Date

On the 2006-2010 BMW M6 S85, the S85 5.0L V10 engine in the E63 M6 (2006-2010) has catastrophically tight rod bearing clearances (0.001" vs 0.0025" industry standard) with thin OEM bearings that fail prematurely, leading to spun bearings and complete engine destruction. This is the single most critical issue on any BMW M car. OEM bearings are inadequate - they WILL fail, typically between 60,000-100,000 miles, often sooner with track use. Failure modes include sudden loss of oil pressure, knocking, and seized engine. Blackstone Labs oil analysis every 5,000 miles ($30/test) is mandatory to monitor bearing wear metals (copper, lead, tin). If copper levels spike above 30 PPM, bearings are failing and must be replaced immediately. NEVER use OEM bearings as replacements - use ACL Race Bearings with +0.001" extra clearance. Bimmerpost/M5Board consensus: this is MANDATORY preventive maintenance before 70,000 miles.

This issue also affects: Citroën C3, Hyundai Santa Fe, Hyundai Tucson

Common Symptoms

Engine knocking or ticking noise (bearing wear)
Sudden loss of oil pressure (bearing failure in progress)
Metal particles in oil or on magnetic drain plug
Elevated copper/lead/tin in Blackstone Labs oil analysis
Engine seizure (catastrophic failure)
Oil pressure warning light

How to Fix

MANDATORY PREVENTIVE REPLACEMENT before 70,000 miles: Replace all 10 rod bearings with ACL Race Bearings 10B1580HX-STD (+0.001" clearance, $200-350) or WPC-treated bearings from Lang Racing, or VAC Motorsports kit VAC-HPRBK-S85, or Turner kit TMS222798, or FCP Euro kit 11247841703KT3. ALSO replace VANOS line 11367838669 and use ARP rod bolts (included in most kits). Cost: $6,500-9,500 preventive. If engine is destroyed from bearing failure: $15,000-32,000 for engine replacement or rebuild. NEVER use OEM bearings as replacements. Use Blackstone Labs oil analysis every 5,000 miles ($30/test) to monitor bearing wear metals.

What Owners Are Using

Parts and tips from 0+ owners who fixed this issue

UpgradeACL Race Bearings 10B1580HX-STD with +0.001" extra clearance ($200-350) are THE standard replacement. NEVER use OEM bearings. Also consider VAC Motorsports kit VAC-HPRBK-S85 or Turner kit TMS222798. (ACL Race Rod Bearings 10B1580HX-STD)
View on Amazon
NoteMANDATORY before 70,000 miles. This is not optional maintenance - it is a question of WHEN the OEM bearings fail, not IF. Budget $6,500-9,500 for preventive replacement.
TipUse Blackstone Labs oil analysis every 5,000 miles ($30/test) to monitor copper, lead, and tin levels. If copper spikes above 30 PPM, bearings are failing - replace immediately.
UpgradeWPC-treated bearings from Lang Racing offer the best durability for track use. Also replace VANOS line 11367838669 and use ARP rod bolts during the job. (Lang Racing WPC-Treated Rod Bearings)
View on Amazon

Typical repair cost:$6,500 - $32,000

Research This Issue

0+ owners have reported this issue

Google Reddit YouTube NHTSA

Community Reported

Medium Confidence0 reportsLast reported by owners Invalid DateReviewed Invalid Date

On the 2005-2010 BMW M6, the E63/E64 M6 uses a Sequential Manual Gearbox (SMG III) that relies on a hydraulic pump and actuator to operate the clutch. The SMG pump is prone to failure, typically between 60,000 and 90,000 miles. When the pump fails, the car displays "SMG Transmission Fault" and may become undrivable. The hydraulic accumulator (pressure sphere) also loses its charge over time, causing slow or jerky shifts before complete failure.

Common Symptoms

SMG Transmission Fault warning on iDrive
Slow or jerky gear changes
Grinding noise during gear engagement
Car stuck in gear or unable to select gear
Hydraulic pump running constantly

How to Fix

Replace the SMG hydraulic pump and pressure accumulator. Bleed and refill the SMG hydraulic system with Pentosin CHF 11S fluid. Many owners convert to a traditional 6-speed manual swap using an aftermarket kit from companies like OS Giken or using the E90 M3 6MT parts. Budget $2,000-4,000 for SMG repair or $5,000-8,000 for a manual conversion.

What Owners Are Using

Parts and tips from 0+ owners who fixed this issue

Tip
UpgradeReplacement shift solenoid to restore proper gear engagement (Dorman Transmission Shift Solenoid)
View on Amazon
UpgradeTransmission filter kit with gasket for fluid service after solenoid replacement (ATP Transmission Filter Kit)
View on Amazon

Typical repair cost:$2,000 - $4,000

Research This Issue

0+ owners have reported this issue

Google Reddit YouTube NHTSA

Community Reported

Medium Confidence0 reportsLast reported by owners Invalid DateReviewed Invalid Date

On the 2006-2010 BMW M6 S85, the S85 V10 engine in the E63 M6 (2006-2010) uses individual throttle bodies with internal throttle actuators containing plastic PPA (polyphthalamide) gears that strip over time, typically around 70,000 miles. The plastic gear teeth are gradually worn down by the metal worm drive, causing the throttle body to lose position control. When the gears strip, the affected bank of cylinders loses throttle control, causing limp mode, rough running, and diagnostic codes 2B15 or 2B16 (throttle actuator faults). The S85 has 2 throttle actuators (one per bank of 5 cylinders) - both should be rebuilt at the same time. Beisan Systems sintered metal replacement gears are the permanent fix - they outlast the plastic OEM gears indefinitely. This is a well-documented issue on M5Board and Bimmerpost.

This issue also affects: BMW M5

Common Symptoms

Check engine light with codes 2B15 or 2B16 (throttle actuator fault)
Limp mode / reduced power mode
Rough idle or engine running on fewer cylinders
Throttle response becomes erratic or delayed
Engine hesitation on acceleration
One bank of cylinders not responding to throttle input

How to Fix

Rebuild throttle actuators using Beisan Systems BS101 sintered metal gear kit ($250/set, need 2 sets for both actuators) for permanent fix. Beisan BS102 full rebuild service available ($300). Alternatively, rebuilt actuators from Euro Power Motorsports ($500-800 each). OEM replacement actuators from BMW cost $2,000-4,500. Total cost: $500-4,500 depending on approach. Beisan Systems sintered metal gears are THE permanent fix - they replace the weak plastic PPA gears with metal gears that will not strip. Always rebuild both actuators simultaneously.

What Owners Are Using

Parts and tips from 0+ owners who fixed this issue

UpgradeBeisan Systems BS101 sintered metal gear kit ($250/set, need 2) is THE permanent fix. Metal gears replace weak plastic PPA gears and will not strip again. (Beisan Systems BS101 Throttle Actuator Gear Kit)
View on Amazon
TipAlways rebuild both throttle actuators at the same time - if one has stripped gears, the other is not far behind. Save on labor by doing both.
UpgradeBeisan BS102 full rebuild service ($300) if you prefer not to DIY. Euro Power Motorsports also sells rebuilt actuators ($500-800 each). (Beisan Systems BS102 Rebuild Service)
View on Amazon
NoteOEM BMW replacement actuators use the same plastic gears that will fail again. Only Beisan Systems sintered metal gears are a permanent solution.

Typical repair cost:$500 - $4,500

Research This Issue

0+ owners have reported this issue

Google Reddit YouTube NHTSA

Community Reported

Medium Confidence0 reportsLast reported by owners Invalid DateReviewed Invalid Date

Frequently Asked Questions

What are the most common BMW M6 problems?

According to Au7o's analysis of 0+ owner reports, the 2007-2007 BMW M6 has 4 documented issues. The most frequently reported are: SMG Hydraulic Pump and Clutch Actuator Failure, Rod Bearing Premature Wear (S65/S63 Engines), S85 V10 Rod Bearing Failure (Catastrophic Engine Destruction). Of these, 3 are rated critical and should be addressed promptly.

Is the BMW M6 reliable?

The 2007-2007 BMW M6 has 4 known issues documented across 0+ owner reports. 3 issues are rated critical: SMG Hydraulic Pump and Clutch Actuator Failure and Rod Bearing Premature Wear (S65/S63 Engines) and S85 V10 Rod Bearing Failure (Catastrophic Engine Destruction). Prospective buyers should inspect for these issues and factor potential repair costs into their purchase decision. Regular maintenance following the manufacturer's schedule helps prevent many common problems.

How much does it cost to fix common BMW M6 problems?

Repair costs for known BMW M6 issues range from $500 to $32,000, depending on the specific problem and whether you choose DIY or professional repair. The most critical issue, SMG Hydraulic Pump and Clutch Actuator Failure, typically costs $2,000-$4,000 to repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.

What is the 2005-2010 BMW M6 SMG Hydraulic Pump and Clutch Actuator Failure?

The E63/E64 M6 uses a Sequential Manual Gearbox (SMG III) that relies on a hydraulic pump and actuator to operate the clutch. The SMG pump is prone to failure, typically between 60,000 and 90,000 miles. When the pump fails, the car displays "SMG Transmission Fault" and may become… Repairs typically run $2,000-$4,000. Severity: high.

What is the 2005-2019 BMW M6 Rod Bearing Premature Wear (S65/S63 Engines)?

Both the S65 V8 (E63 M6) and S63 twin-turbo V8 (F06/F12/F13 M6) suffer from premature rod bearing wear. The S65 is particularly notorious — the OEM rod bearings use a copper-lead composition that wears rapidly, especially with frequent cold starts and short trips. The S63 has imp… Repairs typically run $3,000-$6,000. Severity: high.

What is the 2006-2010 BMW M6 S85 V10 Rod Bearing Failure (Catastrophic Engine Destruction)?

The S85 5.0L V10 engine in the E63 M6 (2006-2010) has catastrophically tight rod bearing clearances (0.001" vs 0.0025" industry standard) with thin OEM bearings that fail prematurely, leading to spun bearings and complete engine destruction. This is the single most critical issue… Repairs typically run $6,500-$32,000. Severity: high.

What is the 2006-2010 BMW M6 S85 V10 Throttle Actuator Failure (Plastic Gear Stripping)?

The S85 V10 engine in the E63 M6 (2006-2010) uses individual throttle bodies with internal throttle actuators containing plastic PPA (polyphthalamide) gears that strip over time, typically around 70,000 miles. The plastic gear teeth are gradually worn down by the metal worm drive… Repairs typically run $500-$4,500. Severity: medium.

2007 BMW M6 Problems: 4 Issues Every Owner Should Know

All 4 Known Issues

When Issues Typically Appear

2005-2019 BMW M6: Rod Bearing Premature Wear (S65/S63 Engines)#

Common Symptoms

How to Fix

What Owners Are Using

Research This Issue

2006-2010 BMW M6: S85 V10 Rod Bearing Failure (Catastrophic Engine Destruction)#

Common Symptoms

How to Fix

What Owners Are Using

Research This Issue

2005-2010 BMW M6: SMG Hydraulic Pump and Clutch Actuator Failure#

Common Symptoms

How to Fix

What Owners Are Using

Research This Issue

2006-2010 BMW M6: S85 V10 Throttle Actuator Failure (Plastic Gear Stripping)#

Common Symptoms

How to Fix

What Owners Are Using

Research This Issue

Other BMW Models

Frequently Asked Questions

What are the most common BMW M6 problems?

Is the BMW M6 reliable?

How much does it cost to fix common BMW M6 problems?

What is the 2005-2010 BMW M6 SMG Hydraulic Pump and Clutch Actuator Failure?

What is the 2005-2019 BMW M6 Rod Bearing Premature Wear (S65/S63 Engines)?

What is the 2006-2010 BMW M6 S85 V10 Rod Bearing Failure (Catastrophic Engine Destruction)?

What is the 2006-2010 BMW M6 S85 V10 Throttle Actuator Failure (Plastic Gear Stripping)?