1998 model year · 0+ owner reports · Updated April 2026
According to Au7o's analysis of 0+ owner reports, the 1998 Chevrolet Blazer S-10 has 3 documented known issues. No issues are rated critical, indicating generally reliable ownership. Across all issues, repair costs range from $50 to $900. DIY maintenance guides at au7o.io.
On the 1998-2005 Chevrolet Blazer S-10, the front axle thermal actuator (push-button 4WD models) and transfer case encoder motor fail, preventing engagement or disengagement of 4WD. The thermal actuator uses coolant heating to engage, which is slow and unreliable.
Diagnose the system by checking for transfer case control module codes, verifying 4WD switch operation, and confirming power/ground at the front axle actuator and transfer case encoder motor; also inspect the vacuum/electrical connectors and front axle engagement fork for damage. On push-button 4WD models, replace the original thermal actuator with the updated GM motor-style actuator conversion kit and spacer, which engages faster and more reliably; if the transfer case will not shift or sets encoder-related faults, replace the encoder motor assembly and clean/corrosion-proof the connector. After repair, verify 2HI/4HI/4LO operation on a lift and road test to confirm the front axle fully engages and disengages. Typical cost is about $150-$300 for the updated front actuator kit installed, or roughly $300-$700 for an encoder motor replacement depending on labor rates and parts quality.
Parts and tips from 0+ owners who fixed this issue
On the 1996-2005 Chevrolet Blazer S-10 4.3L Vortec V6, same as the S-10 truck - the 4.3L Vortec V6 develops intake manifold gasket leaks. The Blazer version is identical mechanically.
Pressure-test the cooling system and inspect the front and rear edges of the lower intake manifold for external coolant seepage; on the 4.3L Vortec, leaks are commonly caused by the original lower intake manifold gaskets deteriorating. The proper repair is to remove the upper plenum and lower intake manifold, replace the lower intake manifold gaskets with the updated metal/rubber design, install new intake bolts if specified, and refill with fresh coolant and engine oil if contamination is present. While apart, inspect the distributor, heater hose fittings, and CPI/CSFI lines for related age-related failures, then torque the intake in the correct sequence to spec. Typical repair cost is about $700-$1,300 depending on labor rates and whether coolant/oil contamination or additional tune-up parts are needed.
Parts and tips from 0+ owners who fixed this issue
On the 1998-2004 Chevrolet Blazer S-10, the 1998-2004 S-10 Blazer (and related S-10, GMC Jimmy, GMC Sonoma) dashboards crack severely from UV exposure and heat cycling. The instrument panel trim pad warps, splits, and crumbles. This is a known manufacturing defect in the dashboard material used across the entire S-10 platform during these years.
Confirm the failure is cosmetic dashboard substrate deterioration rather than loose trim by inspecting for cracks around the defroster vents, gauge hood, and passenger airbag area, then checking whether the dash pad has lifted or become brittle from sun exposure. The permanent repair is replacement of the upper instrument panel pad/dash cap assembly with a new OEM, NOS, or quality aftermarket molded cap; this typically requires removing trim panels, cluster bezel, defroster grille fasteners, and in some cases partially lowering the steering column for access. If the original pad is badly fragmented, many owners install a full overlay dash cap bonded with automotive urethane or silicone after trimming loose material, which is cheaper but less factory-correct. Typical cost is about $150-$350 for an aftermarket cap, $400-$900 for a replacement dash pad if available, and roughly 4-8 hours labor, bringing total installed cost to about $500-$1,500 depending on parts source and interior disassembly required.
Parts and tips from 0+ owners who fixed this issue
Don't see your problem? Describe your symptoms to get a diagnosis, or get a full repair guide.
According to Au7o's analysis of 0+ owner reports, the 1998-1998 Chevrolet Blazer S-10 has 3 documented issues. The most frequently reported are: 4WD Thermal Actuator and Encoder Motor Failure, 4.3L V6 Intake Manifold Gasket Leak, Dashboard Cracking and Warping. None are rated critical, but regular maintenance is recommended.
The 1998-1998 Chevrolet Blazer S-10 has 3 known issues documented across 0+ owner reports. No issues are rated critical, suggesting generally good reliability. Regular maintenance following the manufacturer's schedule helps prevent many common problems.
Repair costs for known Chevrolet Blazer S-10 issues range from $50 to $900, depending on the specific problem and whether you choose DIY or professional repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.
The front axle thermal actuator (push-button 4WD models) and transfer case encoder motor fail, preventing engagement or disengagement of 4WD. The thermal actuator uses coolant heating to engage, which is slow and unreliable. Repairs typically run $200-$700. Severity: medium.
Same as the S-10 truck - the 4.3L Vortec V6 develops intake manifold gasket leaks. The Blazer version is identical mechanically. Repairs typically run $400-$900. Severity: medium.
The 1998-2004 S-10 Blazer (and related S-10, GMC Jimmy, GMC Sonoma) dashboards crack severely from UV exposure and heat cycling. The instrument panel trim pad warps, splits, and crumbles. This is a known manufacturing defect in the dashboard material used across the entire S-10 p… Repairs typically run $50-$500. Severity: low.
Content on this page was compiled with AI assistance using NHTSA complaints, TSBs, owner reports, and public automotive data. While we strive for accuracy, this information may contain errors. Always verify repair procedures and specifications with your vehicle's service manual or a qualified mechanic.
