2000 Chevrolet Silverado 2500HD Problems: 2 Issues Every Owner Should Know
2000 model year · 0+ owner reports · Updated April 2026
According to Au7o's analysis of 0+ owner reports, the 2000 Chevrolet Silverado 2500HD has 2 documented known issues. No issues are rated critical, indicating generally reliable ownership. Across all issues, repair costs range from $100 to $2,000. DIY maintenance guides at au7o.io.
All 2 Known Issues
On the 1999-2025 Chevrolet Silverado 2500HD, the transfer case encoder motor on the Silverado 2500HD (NP246/NP261/NP263 transfer cases) fails, preventing the vehicle from shifting between 2WD, 4WD High, and 4WD Low. The encoder motor is mounted on the outside of the transfer case and uses an electric motor with a position sensor to actuate the shift fork. Moisture ingress, corrosion, and worn motor brushes cause intermittent or complete failure. The "Service 4WD" message appears on the DIC, and the transfer case may get stuck in one mode. Failure is more common in salt-belt states.
Common Symptoms
- "Service 4WD" message on dashboard
- Transfer case will not shift out of 2WD
- Transfer case stuck in 4WD
- Grinding noise when attempting to shift transfer case
- 4WD indicator light flashing
- Clunking when shifting between 2WD and 4WD
How to Fix
Replace the transfer case encoder motor ($100-$250 for parts, $100-$200 labor). The motor is externally mounted on the transfer case and accessible from underneath the vehicle. Also inspect and replace the transfer case wiring connector if corroded — moisture wicking up the connector wires is a common cause of encoder motor failure. After replacement, use a scan tool to relearn the encoder motor position. Apply dielectric grease to the electrical connector to prevent future moisture ingress.
What Owners Are Using
Parts and tips from 0+ owners who fixed this issue
- TipApply dielectric grease to the encoder motor connector when you install the new one. Moisture wicking up the harness connector is the #1 cause of premature encoder motor failure.
- UpgradeMobil 1 75W-90 synthetic gear oil for differential and transfer case (Mobil 1 Synthetic Gear Oil 75W-90)
- UpgradeFel-Pro gasket kit for drivetrain service (Fel-Pro Gasket Kit)
On the 1999-2025 Chevrolet Silverado 2500HD, the exhaust manifold bolts on both the gas V8 (5.3L, 6.0L, 6.6L) and Duramax diesel engines in the Silverado 2500HD are notorious for breaking due to thermal cycling. The bolts snap flush with the cylinder head, causing an exhaust leak that produces a ticking or tapping noise on cold start that quiets as the manifold expands and seals when warm. Broken bolts can also cause exhaust fumes to enter the cabin through the HVAC fresh air intake. The passenger side manifold on V8 gas engines is the most commonly affected.
Common Symptoms
- Ticking or tapping noise on cold start that fades when warm
- Exhaust smell in cabin at idle or low speed
- Visible soot staining around exhaust manifold
- Exhaust leak sound from engine bay
- Failed emissions inspection for exhaust leak
How to Fix
Broken bolts must be drilled out and the holes retapped or repaired with thread inserts (HeliCoil or Time-Sert). This is a skilled repair — the bolt remnants are hardened steel embedded in an aluminum or cast iron head. Cost varies widely: $300-$800 if all bolts can be drilled out successfully, $1,000-$2,000 if a head needs to be removed for access to a deeply broken bolt. Use the updated GM exhaust manifold bolt kit which uses higher-grade bolts and locking flanges. Apply anti-seize compound to all new bolts.
What Owners Are Using
Parts and tips from 0+ owners who fixed this issue
- NoteDo not ignore exhaust manifold bolt failure — exhaust fumes entering the cabin through the HVAC system contain carbon monoxide. This is a health and safety issue, not just a noise annoyance.
- UpgradeDorman exhaust manifold — solves cracking issues on many models (Dorman Exhaust Manifold)
- UpgradeDorman exhaust manifold bolt and stud kit (Dorman Exhaust Manifold Hardware Kit)