According to Au7o's analysis of 7,232+ owner reports, the 2014 Hyundai Sonata has 12 documented known issues, with 6 rated critical. The most serious are Theta II Engine Seizure/Failure ($0-$8,000 repair), Electric Power Steering (EPS) Failure ($400-$1,500 repair), Theta II GDI excessive oil consumption ($2,500-$7,000 repair), Theta II 2.0T/2.4L GDI connecting-rod bearing failure (knock, stall, fire) ($4,000-$8,000 repair), P0016 — Crank/Cam Correlation Fault from Stretched Timing Chain (Theta II 2.4L GDI) ($500-$2,000 repair) and P0420 — Bank 1 Catalytic Converter Failure from Theta II 2.4L GDI Oil Consumption ($900-$2,500 repair). The most commonly reported issue is Theta II Engine Seizure/Failure with 5,632 owner reports. Across all issues with published estimates, repair costs range from $20 to $8,000. DIY maintenance guides at au7o.io.
Hyundai Motor America (Hyundai) is recalling certain 2017-2018 Sonata, 2016-2018 Sonata Hybrid, 2018-2020 Accent, and 2016-2017 Azera vehicles. The trunk latch may become damaged, preventing the opening of the trunk from the inside. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 401, "Internal Trunk Release."
Campaign #21V61900006/08/2021
ELECTRICAL SYSTEM:SOFTWARE
Hyundai Motor America (Hyundai) is recalling certain 2020 Nexo and Sonata vehicles. The Remote Smart Parking Assist (RSPA) software may fail to prevent vehicle movement upon detection of an RSPA system malfunction.
Campaign #20V21300009/04/2020
EQUIPMENT:OTHER:LABELS
Hyundai Motor America (Hyundai) is recalling certain 2020 Sonata vehicles produced between October 22, 2019 and February 13, 2020. The tire pressure label inside the driver's door and the owner's manual state an incorrect tire size. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
🔧
A mechanic who knows YOUR exact car
Answers tuned to your year, make, model & trim — not generic advice. Save your garage so it always has the right context.
Get ahead of Hyundai Sonata problems — free
Leave your email and we'll alert you the moment there's a new recall or known issue for your Hyundai Sonata. Free, no account needed.
According to Au7o's analysis of 7,232+ owner reports, the 2014 Hyundai Sonata has 12 documented issues. The most frequently reported are: Theta II Engine Seizure/Failure, Electric Power Steering (EPS) Failure, Theta II GDI excessive oil consumption. Of these, 6 are rated critical and should be addressed promptly.
Is the Hyundai Sonata reliable?
The 2014 Hyundai Sonata has 12 known issues documented across 7,232+ owner reports. 6 issues are rated critical: Theta II Engine Seizure/Failure and Electric Power Steering (EPS) Failure and Theta II GDI excessive oil consumption and Theta II 2.0T/2.4L GDI connecting-rod bearing failure (knock, stall, fire) and P0016 — Crank/Cam Correlation Fault from Stretched Timing Chain (Theta II 2.4L GDI) and P0420 — Bank 1 Catalytic Converter Failure from Theta II 2.4L GDI Oil Consumption. Prospective buyers should inspect for these issues and factor potential repair costs into their purchase decision. Regular maintenance following the manufacturer's schedule helps prevent many common problems.
How much does it cost to fix common Hyundai Sonata problems?
Repair costs for known Hyundai Sonata issues range from $0 to $8,000, depending on the specific problem and whether you choose DIY or professional repair. The most critical issue, Theta II Engine Seizure/Failure, typically costs $0-$8,000 to repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.
What is the 2011-2019 Hyundai Sonata Theta II Engine Seizure/Failure?
The Theta II engine can seize due to metal debris blocking oil flow to connecting rod bearings. Hyundai issued recalls and extended warranties. Affected engines may need replacement. Repairs typically run $0-$8,000. Severity: high.
What is the 2011-2019 Hyundai Sonata Electric Power Steering (EPS) Failure?
The electric power steering system can fail, causing sudden loss of power assist while driving. This can make the car very difficult to steer, especially at low speeds. A steering warning light usually accompanies the failure. Repairs typically run $400-$1,500. Severity: high.
Content on this page was compiled with AI assistance using NHTSA complaints, TSBs, owner reports, and public automotive data. While we strive for accuracy, this information may contain errors. Always verify repair procedures and specifications with your vehicle's service manual or a qualified mechanic.
Filter:
Community reported
5,632 owners
On the 2011-2019 Hyundai Sonata, the Theta II engine can seize due to metal debris blocking oil flow to connecting rod bearings. Hyundai issued recalls and extended warranties. Affected engines may need replacement.
Check VIN for active recalls - Hyundai provides free engine replacement for affected vehicles. Install the knock sensor detection system (KSDS) software update that monitors for bearing wear. Change oil every 5,000 miles. If engine fails and under warranty, replacement is free. Out of warranty replacement: $4,000-8,000.
Owner tips & cautions
TipDIY repairs can save significantly - dealer charges $4,000-8,000 but DIY costs are typically 50-70% less
WarningThis is a high-severity issue - ignoring it can lead to costly repairs or safety concerns. Address it promptly.
TipGet a proper diagnosis before replacing parts - similar symptoms can have different causes
High ConfidenceVerified5,632 reportsLast reported by owners Feb 2024Reviewed Feb 2026
On the 2011-2021 Hyundai Sonata, owners of Theta II GDI Sonatas report excessive engine oil consumption, with rates reported as high as one quart every 700-1,000 miles - far beyond what the owner's manual considers normal. The condition is tied to the same Theta II design weaknesses (ring/bearing wear and oil-control issues) and frequently precedes low-oil-pressure warnings and rod-bearing knock. Drivers are forced to constantly check and top off oil; if missed, low oil level accelerates bearing damage and engine failure. A nationwide class action (covering 2009-2010 and 2015-2021 Sonata among other Hyundai/Kia models with Theta, Nu, Gamma, Lambda and Kappa engines) alleged the engines burn oil and eventually fail. CarComplaints catalogs dozens of oil-consumption complaints starting with the 2011 model year.
Common Symptoms
Burning ~1 quart of oil per 700-1,000 miles
Low oil level / low oil-pressure warning between changes
Need to add oil far more often than manual specifies
Blue exhaust smoke in some cases
Eventual engine knock or failure if oil runs low
How to Fix
Document consumption with dealer oil-consumption tests (typically measured over ~1,000 miles). If the vehicle qualifies, repairs (often piston/ring or short-block replacement) may be covered under the Theta extended warranty or class-action terms; keep oil-change and top-off records. Check oil level frequently between changes as an interim safeguard and address any oil-pressure or knock warning immediately, since low oil accelerates rod-bearing failure.
On the 2011-2019 Hyundai Sonata, the Theta II GDI engine (2.4L MPI/GDI and 2.0T) suffers premature connecting-rod bearing wear. NHTSA determined that metal debris left from crankshaft machining, plus uneven crankpin surface roughness, restricts oil flow to the rod bearings, raising bearing temperatures and causing premature wear. A worn bearing produces a metallic, cyclic knocking noise that increases with RPM; if driven further the bearing fails, the engine can seize and stall while in motion, and a fractured rod can puncture the block, letting oil reach hot surfaces and start an engine-compartment fire. This is the defect behind multiple recalls (Campaign 132 / NHTSA 15V-218 for 2011-2012 2.0T/2.4 GDI built at HMMA; Campaign 198 / NHTSA 20V-746 covering Sonata Hybrid and others), a $210M NHTSA civil penalty consent order, and a ~$1.3B class-action settlement covering roughly 3.9M Hyundai/Kia owners.
Common Symptoms
Metallic cyclic knocking noise that increases with engine RPM
Have the dealer perform the recall engine-inspection test (rod-bearing/Knock Sensor Detection System diagnostic). If bearing damage is found, the engine is replaced free under the campaign. All affected vehicles receive the KSDS software update that detects pre-failure knock and limits power. Settlement extends powertrain warranty to 15 years / 150,000 miles for rod-bearing failure (transferable to subsequent owners), with reimbursement for prior repairs. If you hear a metallic knock that rises with RPM or see the oil-pressure/check-engine light, stop driving and get it inspected immediately.
On the 2010-2015 Hyundai Sonata 2.4L Theta II GDI I4, on the 2010-2015 Sonata with the 2.4L Theta II GDI engine, P0016 (Crankshaft/Camshaft Position Correlation, Bank 1 Sensor A) most often signals a stretched timing chain or a worn/failing chain tensioner, letting the intake cam fall out of sync with the crank. Poor oil flow and soot/metal debris in these GDI engines accelerate chain stretch and guide wear — the same oil-starvation environment behind the engine's bearing-failure lawsuit. A faulty intake Oil Control Valve (OCV) can also set it. Left unaddressed, the chain can jump time and cause valve-to-piston contact and severe engine damage.
Common Symptoms
Check engine light
Rattle/whine from front of engine at startup
Rough running or misfire
Loss of power
Hard starting
Potential engine damage if ignored
How to Fix
Inspect the timing chain, guides, and tensioner; replace the chain kit (chain, tensioner, guides) if stretched. Verify oil level/quality and correct any oil-consumption problem feeding the wear. Test the intake OCV and replace if faulty. Check for open Theta II recalls/warranty extensions, as related engine repairs may be covered.
Medium ConfidenceVerified0 reportsReviewed Jul 2026
On the 2007-2019 Hyundai Sonata, on the Sonata, P0011 (Intake Camshaft Timing Over-Advanced, Bank 1) is set when the CVVT phasing runs further advanced than commanded. The most common Sonata cause is a failed/clogged intake Oil Control Valve (OCV/VVT solenoid) — the CVVT system uses oil pressure metered by the OCV to phase the cam, so a sticking solenoid or contaminated oil passages drive the cam over-advanced. Low oil level, wrong viscosity, or dirty oil commonly cause or worsen it; a displaced timing chain is a more severe possibility. A useful field test is swapping the intake and exhaust OCVs (identical, one bolt each): if the code migrates to P0014, the moved OCV is the faulty part.
Common Symptoms
Check engine light
Rough idle
Loss of acceleration/power
Hesitation or stalling at idle
Reduced fuel economy
How to Fix
Verify oil level, condition, and correct viscosity first — top up/change oil if degraded. Test the intake OCV (coil resistance ~6.8-8.0 ohms at 68°F) and swap intake/exhaust OCVs to confirm; replace the failed OCV. Clean the OCV oil-feed screen/passages. If timing components are displaced, inspect and correct the timing chain.
On the 2011-2019 Hyundai Sonata 2.4L Theta II GDI I4, on the 2011-2019 Sonata with the 2.4L Theta II GDI engine, P0420 (Catalyst Efficiency Below Threshold, Bank 1) is frequently a downstream symptom of the engine's well-documented excessive oil consumption. As worn rod bearings/rings let the engine burn oil, phosphorus and other contaminants coat and eventually melt the catalyst's honeycomb, killing its efficiency and setting P0420. Replacing only the converter without fixing the oil-burning root cause leads to rapid re-failure. This ties directly into Recall 132 (NHTSA 15V-568) for connecting-rod bearing wear and the KSDS software / extended 15yr-150k-mile short-block warranty.
Common Symptoms
Check engine light
Reduced fuel economy
Sluggish acceleration
Failed emissions test
Rattle from converter
Elevated oil consumption / low oil warnings
How to Fix
First diagnose and correct the underlying oil consumption — check eligibility under Recall 132/KSDS and the extended engine warranty; the short block may be replaced under warranty. Per Hyundai TSB (ECM update for related P0171/P0420 concerns), apply the ECM software update, then replace the failed catalytic converter only after the oil issue is resolved so the new cat does not fail again.
On the 2011-2019 Hyundai Sonata, on the Sonata, P0442 (small EVAP leak, ~0.020-0.060 in) most often comes from a simple sealing failure or the Natural Vacuum Leak Detection (NVLD) assembly. The gas cap O-ring hardens/cracks with age, and rust on the filler-neck sealing surface prevents a good seal. Hyundai has acknowledged (TSB 21-01-035H) that salt/marine environments contaminate the NVLD sensor, and Sonata Hybrid (2011-2015) is specifically prone to NVLD-driven small-leak codes in coastal areas. A canister purge valve that seals poorly can also produce a small leak.
Common Symptoms
Check engine light (no drivability change)
Occasional faint fuel odor
Failed emissions readiness monitor
How to Fix
Start with the cheap items: inspect/replace the gas cap and clean the filler-neck sealing surface with a Scotch-Brite pad. Smoke-test the EVAP system to locate the leak. Replace the NVLD assembly if contaminated/faulty (Hyundai has issued an updated EVAP air-filter kit and NVLD replacement guidance for salt-contaminated units), and replace a leaking purge valve.
Medium ConfidenceVerified0 reportsReviewed Jul 2026
On the 2011-2019 Hyundai Sonata, p0455 (large/gross EVAP leak, ~0.040 in or larger) on the Sonata is most commonly a loose, missing, or failed gas cap, a canister purge valve stuck open (constant EVAP vacuum leak), or a faulty NVLD sensor — the same coastal salt-contamination pattern Hyundai has documented (TSB 21-01-035H) affecting the Sonata/Sonata Hybrid EVAP system. Larger leaks can also come from a cracked EVAP/vent hose or a damaged charcoal canister.
Common Symptoms
Check engine light
Strong fuel/gasoline odor near vehicle
Failed emissions readiness
Sometimes rough idle if purge valve stuck open
How to Fix
Verify the gas cap is tight and its O-ring is intact; replace if degraded. Smoke-test to find the gross leak. Replace a stuck-open canister purge valve or a cracked EVAP line; replace the NVLD assembly if contaminated. Re-run the EVAP monitor to confirm the leak is sealed.
Medium ConfidenceVerified0 reportsReviewed Jul 2026
Community reported
880 owners
On the 2011-2019 Hyundai Sonata, the electric power steering system can fail, causing sudden loss of power assist while driving. This can make the car very difficult to steer, especially at low speeds. A steering warning light usually accompanies the failure.
Common Symptoms
Sudden heavy steering
Steering warning light
Complete loss of power assist
Steering column noise
Intermittent assist
How to Fix
Replace EPS motor or steering column assembly. Have dealer diagnose specific failed component. Check for Hyundai recalls or service campaigns. This is a safety-critical repair.
Owner tips & cautions
WarningThis is a high-severity issue - ignoring it can lead to costly repairs or safety concerns. Address it promptly.
TipGet a proper diagnosis before replacing parts - similar symptoms can have different causes
TipSearch Hyundai Sonata forums and owner groups for real-world experiences and DIY guides
TipGet multiple quotes from independent mechanics - dealer prices can be 2-3x higher for the same repair
High Confidence880 reportsLast reported by owners Feb 2024Reviewed Feb 2026
Community reported
720 owners
On the 2011-2020 Hyundai Sonata, the A/C compressor can fail, particularly on vehicles in hot climates with heavy A/C use. Internal compressor failure can contaminate the A/C system. Clutch and bearing failures are also common.
Common Symptoms
A/C blows warm air
Loud noise when A/C engages
A/C clutch not engaging
Refrigerant leak
A/C works intermittently
How to Fix
Replace A/C compressor assembly. If internal failure, flush entire system, replace condenser, receiver/drier, and expansion valve. Use quality replacement parts. Aftermarket compressors available at lower cost.
Owner tips & cautions
TipConsider OEM parts for critical components like sensors and electrical parts - aftermarket can be unreliable
TipGet a proper diagnosis before replacing parts - similar symptoms can have different causes
High Confidence720 reportsLast reported by owners Feb 2024Reviewed Feb 2026
On the 2006-2015 Hyundai Sonata, on the Hyundai Sonata, P0171 (System Too Lean, Bank 1) is most commonly triggered by unmetered air entering downstream of the MAF sensor. The two dominant Sonata-specific sources are a leaking intake manifold gasket and a canister purge valve that sticks open. Because the MAF never counts this extra air, the ECM under-fuels and long-term fuel trims climb past the lean threshold. A dirty MAF hot-wire element is the third common contributor. On V6 Sonatas the upper intake plenum gasket is a known leak point; on the 2.4L four-cylinder a cracked PCV hose or brittle intake gasket is typical.
Common Symptoms
Check engine light
Rough or unstable idle
Hesitation on acceleration
Slight loss of power
Reduced fuel economy
Occasional lean-related surge
How to Fix
Perform a smoke test of the intake to pinpoint the leak. Replace the intake manifold/plenum gasket if leaking; replace a stuck-open canister purge (solenoid) valve; clean or replace the MAF sensor; inspect and replace cracked PCV hoses. Clear codes and confirm fuel trims return to near zero after the repair.
Medium ConfidenceVerified0 reportsReviewed Jul 2026
On the 2011-2019 Hyundai Sonata, on the Sonata (notably the 2015-2019 2.4L), P0128 sets when the ECM sees the engine failing to reach thermostat regulating temperature within the expected time. The overwhelmingly common cause is a thermostat stuck open — often within the plastic thermostat housing assembly, which becomes brittle and is sold as a unit with the thermostat and seal. The second most likely cause is a faulty engine coolant temperature (ECT) sensor. A tell-tale sign is weak cabin heat, since coolant never fully warms.
Common Symptoms
Check engine light
Weak or cold cabin heat
Temp gauge reads low / slow to warm
Reduced fuel economy
Poor cold-engine performance
How to Fix
Confirm the engine is actually running cool (scan-tool ECT vs. gauge). Replace the thermostat / thermostat housing assembly; note the jiggle valve must be oriented at the top so trapped air bleeds out. Removing the battery and air intake box is typically needed for access. If the thermostat is fine, test/replace the ECT sensor. Refill and bleed the cooling system.
Medium ConfidenceVerified0 reportsReviewed Jul 2026
Campaign #20V12200028/02/2020
LATCHES/LOCKS/LINKAGES:TRUNK LID:LATCH
Hyundai Motor America (Hyundai) is recalling certain 2020 Sonata and Sonata Hybrid, and 2019 Genesis G70 vehicles. The trunk latch may become damaged, preventing the opening of the trunk from the inside. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 401, "Internal Trunk Release."
Campaign #22V19600028/03/2022
FUEL SYSTEM, GASOLINE
Hyundai Motor America (Hyundai) is recalling certain 2020-2023 Sonata vehicles. A damaged check valve can allow air to enter the fuel tank, causing it to expand and contact hot exhaust components, melting the tank.
What is the 2011-2021 Hyundai Sonata Theta II GDI excessive oil consumption?
Owners of Theta II GDI Sonatas report excessive engine oil consumption, with rates reported as high as one quart every 700-1,000 miles - far beyond what the owner's manual considers normal. The condition is tied to the same Theta II design weaknesses (ring/bearing wear and oil-co… Repairs typically run $2,500-$7,000. Severity: high.
What is the 2011-2019 Hyundai Sonata Theta II 2.0T/2.4L GDI connecting-rod bearing failure (knock, stall, fire)?
The Theta II GDI engine (2.4L MPI/GDI and 2.0T) suffers premature connecting-rod bearing wear. NHTSA determined that metal debris left from crankshaft machining, plus uneven crankpin surface roughness, restricts oil flow to the rod bearings, raising bearing temperatures and causi… Repairs typically run $4,000-$8,000. Severity: high.
What is the 2010-2015 Hyundai Sonata P0016 — Crank/Cam Correlation Fault from Stretched Timing Chain (Theta II 2.4L GDI)?
On the 2010-2015 Sonata with the 2.4L Theta II GDI engine, P0016 (Crankshaft/Camshaft Position Correlation, Bank 1 Sensor A) most often signals a stretched timing chain or a worn/failing chain tensioner, letting the intake cam fall out of sync with the crank. Poor oil flow and so… Repairs typically run $500-$2,000. Severity: high.
What is the 2011-2019 Hyundai Sonata P0420 — Bank 1 Catalytic Converter Failure from Theta II 2.4L GDI Oil Consumption?
On the 2011-2019 Sonata with the 2.4L Theta II GDI engine, P0420 (Catalyst Efficiency Below Threshold, Bank 1) is frequently a downstream symptom of the engine's well-documented excessive oil consumption. As worn rod bearings/rings let the engine burn oil, phosphorus and other co… Repairs typically run $900-$2,500. Severity: high.
What is the 2011-2020 Hyundai Sonata A/C Compressor Failure?
The A/C compressor can fail, particularly on vehicles in hot climates with heavy A/C use. Internal compressor failure can contaminate the A/C system. Clutch and bearing failures are also common. Repairs typically run $500-$1,400. Severity: medium.
What is the 2007-2019 Hyundai Sonata P0011 — Intake Cam Over-Advanced from Failed Oil Control Valve (CVVT)?
On the Sonata, P0011 (Intake Camshaft Timing Over-Advanced, Bank 1) is set when the CVVT phasing runs further advanced than commanded. The most common Sonata cause is a failed/clogged intake Oil Control Valve (OCV/VVT solenoid) — the CVVT system uses oil pressure metered by the O… Repairs typically run $120-$450. Severity: medium.
What is the 2006-2015 Hyundai Sonata P0171 — Bank 1 Lean from Intake Manifold Gasket Vacuum Leak / Stuck Purge Valve?
On the Hyundai Sonata, P0171 (System Too Lean, Bank 1) is most commonly triggered by unmetered air entering downstream of the MAF sensor. The two dominant Sonata-specific sources are a leaking intake manifold gasket and a canister purge valve that sticks open. Because the MAF nev… Repairs typically run $90-$550. Severity: medium.
What is the 2011-2019 Hyundai Sonata P0128 — Engine Not Reaching Operating Temp from Stuck-Open Thermostat?
On the Sonata (notably the 2015-2019 2.4L), P0128 sets when the ECM sees the engine failing to reach thermostat regulating temperature within the expected time. The overwhelmingly common cause is a thermostat stuck open — often within the plastic thermostat housing assembly, whic… Repairs typically run $180-$450. Severity: low.
What is the 2011-2019 Hyundai Sonata P0442 — Small EVAP Leak from Gas Cap Seal or NVLD Sensor?
On the Sonata, P0442 (small EVAP leak, ~0.020-0.060 in) most often comes from a simple sealing failure or the Natural Vacuum Leak Detection (NVLD) assembly. The gas cap O-ring hardens/cracks with age, and rust on the filler-neck sealing surface prevents a good seal. Hyundai has a… Repairs typically run $20-$400. Severity: low.
What is the 2011-2019 Hyundai Sonata P0455 — Gross EVAP Leak from Loose/Failed Gas Cap or Stuck Purge Valve?
P0455 (large/gross EVAP leak, ~0.040 in or larger) on the Sonata is most commonly a loose, missing, or failed gas cap, a canister purge valve stuck open (constant EVAP vacuum leak), or a faulty NVLD sensor — the same coastal salt-contamination pattern Hyundai has documented (TSB… Repairs typically run $20-$400. Severity: low.
