P0303 on Ford: How to Diagnose & Fix

The 1.5L EcoBoost in 2014-2019 Ford Fusion is affected by the same open-deck cylinder block design defect as the Escape. Coolant leaks internally from the block passages into the combustion chambers due to insufficient sealing surface and porous block material that cannot maintain coolant pressure over time. Ford extended warranty coverage to 7 years/84,000 miles for short block replacement per TSB 19-2139 and TSB 19-2375. A consolidated class action lawsuit covers 2013-2019 Fusion and Escape with 1.5L, 1.6L, and 2.0L EcoBoost engines. Some owners have experienced engine failure with no warning - no check engine light before coolant hydrolocked the cylinder.

The 2.3L EcoBoost engine in 2015-2019 Mustangs is prone to head gasket failure, particularly in vehicles that experience repeated heat cycles or are driven hard. Block distortion over multiple thermal cycles creates gaps between the engine block and cylinder head that the gasket cannot seal, allowing coolant to enter the cylinders when the engine is cold. Ford redesigned the engine for 2020+ models.

Early 2.3L EcoBoost Mustangs can experience coolant intrusion into the combustion chamber through cracked cylinder head or head gasket failure. This can cause white smoke from exhaust, coolant loss, and potential engine damage if not addressed.

The 2.0L GDI (Gasoline Direct Injection) and 2.0L EcoBoost engines in 2012-2018 Ford Focus accumulate carbon deposits on the intake valves over time because direct injection fuel never washes over the valve faces. Oil vapors from the PCV system coat the intake valves and harden into carbon deposits over 60,000-100,000 miles. As deposits build up, they restrict airflow, cause rough idle, misfires, and reduced power. This is a maintenance issue inherent to all direct-injection engines (BMW, VW, Ford, etc.) and is not covered under warranty except in severe cases. The only effective permanent repair is walnut blasting the intake valves.

The 2017-2023 Ford Transit with the 2.0L EcoBlue diesel engine (available in some markets) and the 3.5L EcoBoost V6 experience fuel injector failures causing rough running, misfires, poor idle, reduced performance, and excessive smoke on cold start. Parkers UK documents an official Ford service action for Transit EcoBlue diesel injector failures traced to a quality issue with Continental-supplied injectors where an internal surface coating comes unstuck, blocking the injector. FordTransitUSAForum.com documents injector failure on 3.5L EcoBoost Transit models as well, where direct injection fuel deposits cause injector spray pattern degradation. RepairPal estimates individual injector replacement between $266 and $627 depending on Transit model, but multiple injectors often need replacement simultaneously, and contaminated fuel systems can cost significantly more.

The 2.0L EcoBoost engine in 2015-2019 Ford Edge is notorious for internal coolant leaks where antifreeze bypasses the head gasket and floods the combustion chambers. Ford's open-deck block design with scored channels between cylinders creates an inadequate sealing surface that degrades over time. Ford acknowledged this in TSB 19-2208 (later TSB 22-2229) and the prescribed fix is complete engine long block replacement costing $7,700-$10,000+. Ford never issued a recall, relying instead on TSBs and limited extended warranty coverage. The 2020+ redesigned closed-deck block resolved this issue. CarComplaints.com lists 43+ complaints for the 2017 Edge alone specifically for coolant leak into cylinder.

The 1.6L EcoBoost engine in 2014-2018 Ford Transit Connect has documented issues with coolant loss, overheating, and in severe cases engine fires. Ford issued Recall 14S11 (NHTSA 14V309) for 2013-2014 models covering coolant leakage from the cylinder head that could contact hot engine components and cause fire. The 1.6L EcoBoost was also susceptible to head gasket failure and internal coolant leaks similar to the 1.5L and 2.0L EcoBoost engines in other Ford models. The engine was discontinued and replaced by the 2.0L EcoBoost in later Transit Connect models. The FordTransitConnectForum documents numerous cases of premature engine failure on 1.6L-equipped vans used in commercial service.

The 1.5L EcoBoost 3-cylinder engine in 2021-2024 Ford Bronco Sport is the latest variant of Ford's troubled EcoBoost coolant intrusion problem. The open-deck block design allows coolant to leak internally into the cylinders, causing misfires, white exhaust smoke, and complete engine failure. Ford issued TSB 25-2063 in February 2025 addressing coolant loss in 2021-2024 Bronco Sport 1.5L models, recommending a coolant system flush to prevent recurrent water pump failures. Ford also extended warranty coverage to 7 years/84,000 miles for short block replacement due to coolant intrusion. BroncoSportForum.com documents numerous cases including owners stranded with brand-new vehicles. NHTSA opened an investigation into EcoBoost engine failures in October 2023 covering multiple Ford models.

The 4.6L 2-valve engine uses spark plugs that thread into aluminum heads with only a few threads of engagement. The plugs can eject from the head under load, stripping the threads. Later models (2004+) use a 2-piece plug design that can break during removal.

The early 2-valve Triton aluminum heads used in the gas Super Duty carry only about four threads in the spark plug bore. Combustion pressure and heat cycling gradually pull those few aluminum threads until the plug backs out and is ejected from the head, often taking the coil-on-plug boot with it. Owners describe a gunshot bang followed by an instant severe misfire and an exhaust-like roar from under the hood. It is the defining failure of the pre-3-valve Triton engines and affects the 6.8L V10 and the 5.4L V8 in the same way. Ford addressed it with a revised head design carrying substantially more thread engagement, so later trucks are not exposed.

The 3.5L EcoBoost in the Flex (SHO-derived, EcoBoost/Limited AWD models) is direct-injected only, so no fuel ever washes across the back of the intake valves. Oil vapor pulled through the PCV system and exhaust residue from valve overlap bake onto the valve stems and seats. As the deposits thicken they disrupt the low-velocity airflow at idle first, producing a rough or lopey cold idle, then progress to misfires under load, hesitation, lost boost response and reduced fuel economy. It is a mileage-driven wear item, not a defect that appears suddenly, and is typically noticeable somewhere past 60,000-80,000 miles depending on driving pattern and oil change discipline.

The 5.4L Triton 2-valve V8 in 1997-2008 Expeditions is notorious for spark plugs ejecting from the aluminum cylinder heads. The 2-valve heads have only 4 threads holding each spark plug, which is insufficient for the clamping force needed. Over time, the threads strip and the spark plug launches out of the head under combustion pressure, taking the ignition coil with it. This typically happens when spark plugs are removed and reinstalled, or spontaneously at high mileage.

The optional 4.6L 2-valve modular V8 (shared with the Mercury Mountaineer) has aluminum heads that engage only a few spark-plug threads (~0.25 in). Under thermal cycling the plug can strip the threads and eject from the head, sometimes blowing out the coil boot with it. Ford acknowledged the stripped/missing-thread condition in TSB 07-21-2 for 1997-2008 4.6/5.4/6.8L 2V engines. Ejection causes a loud pop, sudden misfire and power loss, and a fuel-vapor fire risk.

Explorers (especially the Sport and Platinum) with the twin-turbocharged 3.5L EcoBoost are widely reported to develop cylinder misfires, a flashing check-engine light, rough idle and a loss of power that owners frequently chase by replacing ignition coils and spark plugs. The turbocharged, high-heat environment is hard on plugs; the factory Motorcraft SP-534 plug wears its ground strap prematurely and pre-2018 engines (which lacked port injection) suffered intake-valve carbon buildup that aggravates misfires. A recurring root cause traced on the forums is broken/seized exhaust manifold studs that create a vacuum-style exhaust leak right at the cylinder head, which repeatedly destroys coils and triggers misfire codes until the bolts are addressed. Ford never issued a recall for the manifold studs.

Ford's 2.7L EcoBoost (and related small-displacement EcoBoost engines) is prone to micro-cracks forming in the cylinder head around the exhaust ports, allowing coolant to seep into the combustion chamber. This produces unexplained coolant loss with no external leak, white sweet-smelling exhaust, cold-start misfires, and oil emulsification ('mayonnaise' under the oil cap). Left unaddressed it can cause catastrophic engine damage. The defect is the subject of active consolidated federal class-action litigation covering 2.7L and 3.5L F-150, Bronco, and Edge as of 2026.

First-generation 3.5L EcoBoost F-150s use direct injection only (no port injection), so fuel never washes the back of the intake valves. Oil vapor from the PCV system bakes onto the valves and forms hard carbon deposits that restrict airflow and disturb valve sealing. Owners typically begin noticing symptoms around 80,000-125,000 miles: rough idle, cold-start stumble, hesitation or a misfire/shudder under hard acceleration, and reduced fuel economy. Ford has no approved chemical cleaning procedure for these valves and generally directs replacement rather than service, making walnut-blasting the practical fix. Later Gen 2/Gen 3 3.5L engines added port injection (dual injection) which largely prevents new buildup, so this issue is specific to the 2011-2016 direct-injection-only trucks.