According to Au7o's analysis of 4,280+ owner reports, the 2010 Mercedes-Benz M-Class has 9 documented known issues, with 5 rated critical. The most serious are AIRMATIC Air Suspension Strut and Compressor Failure ($1,000-$3,500 repair), M272 Balance Shaft Sprocket Wear ($2,000-$4,500 repair), 722.9 7G-Tronic Conductor Plate (TCM) Failure and Limp Mode ($300-$1,200 repair), Rear Tail Lamp Seal Water Intrusion Destroying Rear SAM and Lift-Gate Modules ($400-$1,800 repair) and OM642 Diesel Oil Cooler Seal Leak. The most commonly reported issue is AIRMATIC Air Suspension Strut and Compressor Failure with 2,100 owner reports. Across all issues with published estimates, repair costs range from $150 to $4,500. DIY maintenance guides at au7o.io.
On the 2006-2011 Mercedes-Benz M-Class 3.5L V6 M272, the M272 V6 engine in ML350 models is affected by the same balance shaft sprocket wear issue found across all Mercedes M272-equipped vehicles. The idler gear wears prematurely, producing a progressively worsening rattle on startup and eventually causing timing chain faults. This is a well-documented manufacturing defect that Mercedes addressed with updated parts.
Replace the balance shaft gear, idler gear, and chain with updated Mercedes parts. This is the same repair as on the E-Class, C-Class, and CLS with the M272 engine. Budget $2,500-$4,500 depending on shop rates. Use only the updated part numbers.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.
Owner tips & cautions
WarningMercedes lost a class action lawsuit over the M272 balance shaft defect. Check if your VIN qualifies for extended warranty coverage before paying out of pocket.
High Confidence1,400 owner reportsLast reported by owners Aug 2025Reviewed Mar 2026
On the 2006-2012 Mercedes-Benz M-Class, mercedes LI18.30-P-055434 applies to passenger cars and light trucks with engine 642 and confirms external oil traces in the oil-cooler inner-V area or at its drain points. The source identifies leaking seals between the engine block and oil cooler, potentially from incorrect installation. It does not say engine oil contaminates coolant, damages hoses or head gaskets, and it explicitly says the oil cooler itself is not the cause and must not be replaced.
Confirm that the leak originates at the oil-cooler-to-crankcase seals rather than another source, then replace the two seals while following the Mercedes installation procedure. The 2014 bulletin lists gasket A 642 188 04 80 and marks A 642 188 01 80 as obsolete; verify the current supersession and exact VIN in EPC before ordering. Do not replace the oil cooler unless separate diagnosis proves it faulty.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
Genuine Mercedes current OM642 oil-cooler gasket 6421880580
OEMMercedes-Benz 6421880580
Confirmed OM642 oil-cooler seal leak when only the current seals are required, quantity two Fitment/availability: The inspected direct U.S.
Confirmed OM642 oil-cooler seal leak when the full intake-access gasket scope is being renewed Fitment/availability: The inspected FCP catalog identifies this direct OE-supplier kit as a comprehensive seal and gasket kit for oil-cooler s…
High ConfidenceVerifiedLast reported by owners Dec 2025Reviewed Aug 2026
Community reported
2,100 owners
On the 2006-2015 Mercedes-Benz M-Class, the AIRMATIC air suspension on the M-Class is prone to air spring leaks and compressor failures, identical to issues on other Mercedes SUVs. The rubber air spring bladders crack from age and road debris, causing the vehicle to sag and the compressor to overwork. The M-Class weight accelerates wear on all suspension components.
Replace leaking air springs and the compressor if it has failed. Consider replacing all four air springs simultaneously. Arnott and Bilstein offer quality aftermarket alternatives. Some owners convert to conventional coil springs using conversion kits to eliminate the air suspension entirely.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
Arnott P-3214 W164 M-Class AIRMATIC compressor with relay
OEMArnott P-3214
Confirmed failed compressor on a 2006-2011 W164 M-Class equipped with AIRMATIC Fitment/availability: The inspected direct U.S. Confirm VIN, option code 489 and chassis; do not use
As an Amazon Associate, we earn from qualifying purchases; other part links may also earn au7o a commission. Confirm fitment by VIN before buying.
Owner tips & cautions
TipArnott coil spring conversion kits eliminate the air suspension entirely for about $800 total. Many high-mileage ML owners do this to avoid repeated air suspension repairs.
High Confidence2,100 owner reportsLast reported by owners Jan 2026Reviewed Mar 2026
On the 2006-2015 Mercedes-Benz M-Class, the W164 and W166 M-Class front suspension uses multiple control arms with press-fit rubber bushings and integrated ball joints (the W166 lower arm has three bushings; the upper arm has two bushings plus a ball joint). The rubber bushings dry out, crack and wear, and the ball joints develop play. Owners report clunking over bumps, knocking when turning or reversing, a 'wandering' front end and vague/loose steering as the suspension moves through excess play before the wheels respond. Given the heavy SUV weight, these wear items are commonly needed, and worn bushings/ball joints will fail an inspection.
Common Symptoms
Clunking/knocking over bumps
Knock when turning or reversing
Wandering front end
Loose or vague steering
Uneven tire wear
How to Fix
Lift the vehicle and check each wheel for play (top-to-bottom and side-to-side) to isolate worn bushings vs ball joints. Replace the affected upper/lower control arms (often supplied as complete arm + bushing + ball joint assemblies). Perform a four-wheel alignment afterward. Replace in axle pairs for balanced handling.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
Lemforder W164 comprehensive front control-arm kit 164330343507
OEMLemforder 164330343507 kit
Multiple confirmed worn front arms/bushings/joints on a cataloged standard W164 M-Class branch Fitment/availability: The inspected direct U.S.
Lemforder W166 comprehensive front control-arm kit KIT-166330
OEMFCP/Lemforder KIT-166330
Multiple confirmed worn front arms/bushings/joints on a cataloged standard W166 ML250/ML350/ML400 branch Fitment/availability: The inspected direct U.S.
On the 2006-2015 Mercedes-Benz M-Class, the 722.9 7G-Tronic automatic transmission fitted to ML350, ML500/550 and other gasoline M-Class models uses an internal conductor plate that doubles as the transmission control module and houses the input/turbine speed sensors. Heat, ATF breakdown and vibration cause the molded-in speed sensors and the plate's electronics to degrade internally. The transmission then loses the ability to monitor input-shaft speed and torque-converter slip, producing harsh, delayed or 'thumping' shifts that start out intermittent and eventually become permanent. In the worst case the transmission locks into a single gear (typically 2nd) and enters limp mode. This is one of the most widely reported 7G-Tronic faults across the W164/W166 M-Class. Repair is plug-and-play once codes are cleared with a STAR/equivalent scanner.
Diagnose with a Mercedes STAR (or equivalent) scanner. Replace or refurbish the conductor plate (TCM); the connecting 13-pin transmission plug/adapter and ATF + filter are usually replaced at the same time. After installation the stored transmission and body codes MUST be cleared with the scanner or the car will remain in limp mode. Rebuilt/refurbished conductor plates are a much cheaper alternative to full valve-body or transmission replacement.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
On the 2006-2011 Mercedes-Benz M-Class, on the W164 M-Class (and related X164 GL), the rear tail lamp gasket seals fail and the power lift-gate hydraulic arm boot develops stress cracks. Water then runs down inside the rear quarter and tailgate area directly onto the rear Signal Acquisition Module (SAM), the rear fuse box, the power lift-gate control module and the lift-gate hydraulic pump. Once soaked, these modules corrode and fail, producing a cascade of electrical faults. Mercedes issued a recall for MY2009 vehicles (thicker tail-lamp seal + relocated lift-gate control unit), but many earlier and unrepaired cars still suffer. Critically, replacing a water-damaged SAM without first fixing the leak will simply destroy the new module.
Common Symptoms
Multiple random warning lights
Power windows or lights not working
Power lift-gate inoperative
Intermittent electrical faults
Water/dampness in rear cargo area
Corroded rear fuse box
How to Fix
Find and fix the water source first: replace the tail lamp gasket/seals with the updated thicker seal and inspect/replace the cracked tailgate lift-arm rubber boot. Dry out the area, then test and replace the rear SAM, rear fuse box, power lift-gate control module and/or hydraulic pump as needed. Clean or replace corroded connectors. Modules typically require coding after replacement.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
Genuine Mercedes W164 left tail-light gasket 1648261591
OEMMercedes-Benz 1648261591
Water-test-confirmed leak at the left W164 tail-lamp gasket Fitment/availability: The inspected direct U.S. Confirm VIN, side an
On the 2006-2015 Mercedes-Benz M-Class, the 4MATIC transfer case chain in the M-Class stretches over time, producing a noticeable whining noise that increases with speed. The chain drives the torque split between front and rear axles, and excessive stretch causes imprecise torque distribution and eventually transfer case failure. Regular fluid changes help prevent premature chain wear.
If caught early, a transfer case fluid change can slow progression. Advanced chain wear requires transfer case removal and rebuild or replacement. The chain, sprockets, and bearings should all be replaced during a rebuild. Use only Mercedes-approved transfer case fluid.
Owner tips & cautions
TipChange the transfer case fluid every 40,000 miles. Mercedes does not include this in the standard service schedule, but it is critical for these heavy AWD SUVs.
Medium Confidence780 owner reportsLast reported by owners Nov 2025Reviewed Mar 2026
On the 2006-2011 Mercedes-Benz M-Class, unlike the earlier W163, the W164 M-Class no longer uses a separate, serviceable brake-light switch; the function is integrated into the brake booster assembly. When this booster-mounted switch/sensor signal degrades, owners experience a cluster of warning messages - ESP/BAS inoperative, cruise control disabled, 'run-flat indicator inoperative' - and sometimes erratic brake-light behavior or a no-start. Because the switch cannot be individually replaced, diagnosis can be confusing, and the symptom set overlaps with ABS pump and wheel-speed-sensor faults that are also common on these models. A scan tool is required to pin down the cause.
Common Symptoms
ESP/BAS inoperative warning
Cruise control will not engage
Run-flat indicator inoperative message
Erratic brake lights
Occasional no-start
How to Fix
Read fault codes with a capable scan tool to distinguish the brake-switch/booster signal fault from ABS pump or wheel-speed-sensor faults. If the booster-integrated switch is at fault, the brake booster assembly is replaced (the switch is not separately serviceable on W164). Verify and clear codes, then road-test ESP/BAS and cruise functionality.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
Genuine Mercedes W164 power brake booster 2514300000
OEMMercedes-Benz 2514300000
Confirmed W164 booster-integrated signal or booster assembly failure on a cataloged ML320/ML350/ML500 branch Fitment/availability: The inspected direct U.S.
On the 2006-2015 Mercedes-Benz M-Class OM642 V6 3.0L diesel, the OM642 3.0L V6 diesel in the ML320/350 CDI and BlueTEC uses intake manifold swirl flaps actuated by plastic linkage rods ('swirl rods') and an electric swirl motor. Constant under-hood heat cycling makes the plastic linkage brittle, while carbon and oil from the crankcase breather make the flaps sticky; the combination snaps the plastic rods. Oil weeping from the turbo inlet seal can also drip onto and kill the swirl motor. The result is rough idle, power loss, an illuminated MIL and possible failed emissions inspection - a relevant concern for EU diesel periodic inspection.
Replace the broken plastic swirl rods with upgraded metal/aluminium swirl rods (direct fit, far more durable) and clean carbon from the flaps and intake. Replace a failed swirl flap motor if oil-contaminated and address the turbo inlet seal leak that caused it. As a stop-gap some owners fit a ~4.7k-ohm resistor across the swirl-motor connector to satisfy the ECU, though this does not restore swirl-flap function.
What you need to fix it
Only diagnosis- and fitment-reviewed repair parts are linked here.
Confirmed broken external swirl linkage with freely moving flaps on a cataloged OM642 M-Class application Fitment/availability: The inspected direct U.S. page identifies genuine Mercedes 6421440035 and explicitly lists W164 ML320 CDI/Blu…
What are the most common Mercedes-Benz M-Class problems?
According to Au7o's analysis of 4,280+ owner reports, the 2010 Mercedes-Benz M-Class has 9 documented issues. The most frequently reported are: AIRMATIC Air Suspension Strut and Compressor Failure, M272 Balance Shaft Sprocket Wear, 722.9 7G-Tronic Conductor Plate (TCM) Failure and Limp Mode. Of these, 5 are rated critical and should be addressed promptly.
Is the Mercedes-Benz M-Class reliable?
The 2010 Mercedes-Benz M-Class has 9 known issues documented across 4,280+ owner reports. 5 issues are rated critical: AIRMATIC Air Suspension Strut and Compressor Failure and M272 Balance Shaft Sprocket Wear and 722.9 7G-Tronic Conductor Plate (TCM) Failure and Limp Mode and Rear Tail Lamp Seal Water Intrusion Destroying Rear SAM and Lift-Gate Modules and OM642 Diesel Oil Cooler Seal Leak. Prospective buyers should inspect for these issues and factor potential repair costs into their purchase decision. Regular maintenance following the manufacturer's schedule helps prevent many common problems.
How much does it cost to fix common Mercedes-Benz M-Class problems?
Repair costs for known Mercedes-Benz M-Class issues range from $150 to $4,500, depending on the specific problem and whether you choose DIY or professional repair. The most critical issue, AIRMATIC Air Suspension Strut and Compressor Failure, typically costs $1,000-$3,500 to repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.
What is the 2006-2015 Mercedes-Benz M-Class AIRMATIC Air Suspension Strut and Compressor Failure?
The AIRMATIC air suspension on the M-Class is prone to air spring leaks and compressor failures, identical to issues on other Mercedes SUVs. The rubber air spring bladders crack from age and road debris, causing the vehicle to sag and the compressor to overwork. The M-Class weigh… Repairs typically run $1,000-$3,500. Severity: high.
What is the 2006-2011 Mercedes-Benz M-Class M272 Balance Shaft Sprocket Wear?
The M272 V6 engine in ML350 models is affected by the same balance shaft sprocket wear issue found across all Mercedes M272-equipped vehicles. The idler gear wears prematurely, producing a progressively worsening rattle on startup and eventually causing timing chain faults. This… Repairs typically run $2,000-$4,500. Severity: high.
Content on this page was compiled with AI assistance using NHTSA complaints, TSBs, owner reports, and public automotive data. While we strive for accuracy, this information may contain errors. Always verify repair procedures and specifications with your vehicle's service manual or a qualified mechanic.
What is the 2006-2015 Mercedes-Benz M-Class 722.9 7G-Tronic Conductor Plate (TCM) Failure and Limp Mode?
The 722.9 7G-Tronic automatic transmission fitted to ML350, ML500/550 and other gasoline M-Class models uses an internal conductor plate that doubles as the transmission control module and houses the input/turbine speed sensors. Heat, ATF breakdown and vibration cause the molded-… Repairs typically run $300-$1,200. Severity: high.
What is the 2006-2011 Mercedes-Benz M-Class Rear Tail Lamp Seal Water Intrusion Destroying Rear SAM and Lift-Gate Modules?
On the W164 M-Class (and related X164 GL), the rear tail lamp gasket seals fail and the power lift-gate hydraulic arm boot develops stress cracks. Water then runs down inside the rear quarter and tailgate area directly onto the rear Signal Acquisition Module (SAM), the rear fuse… Repairs typically run $400-$1,800. Severity: high.
What is the 2006-2012 Mercedes-Benz M-Class OM642 Diesel Oil Cooler Seal Leak?
Mercedes LI18.30-P-055434 applies to passenger cars and light trucks with engine 642 and confirms external oil traces in the oil-cooler inner-V area or at its drain points. The source identifies leaking seals between the engine block and oil cooler, potentially from incorrect ins… Severity: high.
What is the 2006-2015 Mercedes-Benz M-Class Transfer Case Chain Wear and Whining Noise?
The 4MATIC transfer case chain in the M-Class stretches over time, producing a noticeable whining noise that increases with speed. The chain drives the torque split between front and rear axles, and excessive stretch causes imprecise torque distribution and eventually transfer ca… Repairs typically run $500-$3,000. Severity: medium.
What is the 2006-2011 Mercedes-Benz M-Class Brake-Booster-Integrated Brake Light Switch Causing ESP and Cruise Control Faults?
Unlike the earlier W163, the W164 M-Class no longer uses a separate, serviceable brake-light switch; the function is integrated into the brake booster assembly. When this booster-mounted switch/sensor signal degrades, owners experience a cluster of warning messages - ESP/BAS inop… Repairs typically run $250-$1,200. Severity: medium.
What is the 2006-2015 Mercedes-Benz M-Class Front Control Arm Bushing and Ball Joint Wear (Steering Wander and Clunk)?
The W164 and W166 M-Class front suspension uses multiple control arms with press-fit rubber bushings and integrated ball joints (the W166 lower arm has three bushings; the upper arm has two bushings plus a ball joint). The rubber bushings dry out, crack and wear, and the ball joi… Repairs typically run $300-$1,500. Severity: medium.
What is the 2006-2015 Mercedes-Benz M-Class OM642 Diesel Intake Swirl Flap and Linkage (Swirl Rod) Failure?
The OM642 3.0L V6 diesel in the ML320/350 CDI and BlueTEC uses intake manifold swirl flaps actuated by plastic linkage rods ('swirl rods') and an electric swirl motor. Constant under-hood heat cycling makes the plastic linkage brittle, while carbon and oil from the crankcase brea… Repairs typically run $150-$700. Severity: medium.
