According to Au7o's analysis of 2,880+ owner reports, the 2014 GMC Sierra 2500HD has 11 documented known issues, with 7 rated critical. The most serious are CP4.2 High-Pressure Fuel Pump Catastrophic Failure ($8,000-$18,000 repair), LML Duramax EGR Cooler and EGR Valve Failure ($1,200-$3,500 repair), Allison 1000/2000 Transmission TCM Failure and Harsh Shifting ($300-$4,500 repair), 6.0L V8 Excessive Oil Consumption and AFM Lifter Wear ($400-$7,000 repair), Engine Vacuum Pump Output Decay Reducing Power Brake Assist (Recall 19V645000) ($0-$700 repair), Ignition Lock Actuator Binding, Key Sticking and Unintended Rotation Out of RUN (Recalls 14V827000 / 15V640000) ($0-$0 repair) and LML DEF Tank Heater, DEF Injector and NOx Sensor Failures Triggering Speed-Limited Limp Mode ($400-$2,500 repair). The most commonly reported issue is CP4.2 High-Pressure Fuel Pump Catastrophic Failure with 920 owner reports. Across all issues with published estimates, repair costs range from $250 to $18,000.
What are the most common GMC Sierra 2500HD problems?
According to Au7o's analysis of 2,880+ owner reports, the 2014 GMC Sierra 2500HD has 11 documented issues. The most frequently reported are: CP4.2 High-Pressure Fuel Pump Catastrophic Failure, LML Duramax EGR Cooler and EGR Valve Failure, Allison 1000/2000 Transmission TCM Failure and Harsh Shifting. Of these, 7 are rated critical and should be addressed promptly.
Is the GMC Sierra 2500HD reliable?
The 2014 GMC Sierra 2500HD has 11 known issues documented across 2,880+ owner reports. 7 issues are rated critical: CP4.2 High-Pressure Fuel Pump Catastrophic Failure and LML Duramax EGR Cooler and EGR Valve Failure and Allison 1000/2000 Transmission TCM Failure and Harsh Shifting and 6.0L V8 Excessive Oil Consumption and AFM Lifter Wear and Engine Vacuum Pump Output Decay Reducing Power Brake Assist (Recall 19V645000) and Ignition Lock Actuator Binding, Key Sticking and Unintended Rotation Out of RUN (Recalls 14V827000 / 15V640000) and LML DEF Tank Heater, DEF Injector and NOx Sensor Failures Triggering Speed-Limited Limp Mode. Prospective buyers should inspect for these issues and factor potential repair costs into their purchase decision. Regular maintenance following the manufacturer's schedule helps prevent many common problems.
How much does it cost to fix common GMC Sierra 2500HD problems?
Repair costs for known GMC Sierra 2500HD issues range from $0 to $18,000, depending on the specific problem and whether you choose DIY or professional repair. The most critical issue, CP4.2 High-Pressure Fuel Pump Catastrophic Failure, typically costs $8,000-$18,000 to repair. Au7o provides step-by-step DIY maintenance guides that can help reduce repair costs.
What is the 2011-2020 GMC Sierra 2500HD CP4.2 High-Pressure Fuel Pump Catastrophic Failure?
The Bosch CP4.2 high-pressure fuel injection pump used on the 2011-2016 LML and 2017-2020 L5P Duramax diesel engines is prone to catastrophic failure that destroys the entire fuel injection system. Unlike its predecessor the CP3, the CP4.2 lacks a roller element and relies solely… Repairs typically run $8,000-$18,000. Severity: high.
Content on this page was compiled with AI assistance using NHTSA complaints, TSBs, owner reports, and public automotive data. While we strive for accuracy, this information may contain errors. Always verify repair procedures and specifications with your vehicle's service manual or a qualified mechanic.
Filter:
Community reported
920 owners
On the 2011-2020 GMC Sierra 2500HD, the Bosch CP4.2 high-pressure fuel injection pump used on the 2011-2016 LML and 2017-2020 L5P Duramax diesel engines is prone to catastrophic failure that destroys the entire fuel injection system. Unlike its predecessor the CP3, the CP4.2 lacks a roller element and relies solely on fuel for lubrication. When metal fatigue occurs, the pump shatters and sends metal debris throughout the entire high-pressure fuel system — contaminating all six injectors, the fuel rails, return lines, and feed lines. Total repair cost runs $8,000-18,000. A class action lawsuit was filed against GM. The same pump also fails in Ford 6.7 Power Stroke and Ram 6.7 Cummins of the same era.
Replace entire high-pressure fuel system: CP4 pump, all 6 injectors, both fuel rails, return lines, and flush the lift pump/FASS system. Install aftermarket CP3 conversion kit (Fleece FPE-CP3K-LML or FPE-CP3K-L5P) to replace the CP4.2 with the more durable CP3 design. Add a FASS or AirDog lift pump to improve fuel supply. Prevention: never run below 1/4 tank, use quality diesel fuel.
High Confidence920 owner reportsLast reported by owners Feb 2026Reviewed Feb 2026
Community reported
640 owners
On the 2011-2016 GMC Sierra 2500HD 6.6L Duramax LML, the LML Duramax EGR (exhaust gas recirculation) cooler is prone to coolant leaks internally, allowing coolant to enter the intake manifold and combustion chambers. Coolant in the intake causes white smoke, rough running, and potential hydrolocking of cylinders. The EGR valve also sticks open or closed from carbon buildup, causing rough idle, black smoke, and check engine lights. The EGR cooler failure can occur as early as 60,000 miles on trucks used in stop-and-go driving. GM issued multiple TSBs addressing EGR cooler design improvements.
Black smoke and poor fuel economy (EGR valve stuck open)
How to Fix
Replace EGR cooler with updated GM design or aftermarket stainless steel unit (Mishimoto MMEGR-DMAX-LML). Clean or replace EGR valve. Flush cooling system and inspect for coolant contamination in intake. Consider EGR delete kit for off-road/race use only (illegal for street use). Prevent premature failure by maintaining proper coolant pH and avoiding extended idle periods.
High Confidence640 owner reportsLast reported by owners Feb 2026Reviewed Feb 2026
Community reported
430 owners
On the 2014-2020 GMC Sierra 2500HD, the 6.0L L96 V8 gasoline engine in Sierra 2500HD (non-diesel) suffers from Active Fuel Management (AFM) lifter failures similar to the 5.3L in Sierra 1500 — though less frequently due to the higher displacement. More commonly, 6.0L engines exhibit excessive oil consumption (1 qt per 1,000-3,000 miles) from worn valve stem seals and piston rings, particularly between 100,000-150,000 miles. The L96 is a high-output truck engine subjected to heavy towing and payload, which accelerates wear on AFM components.
AFM disabler device (Range Technology RA003B) to prevent lifter wear. Oil consumption: GM oil consumption test procedure — if over 1 qt/2,000 miles, piston ring replacement authorized. Change oil every 5,000 miles with full synthetic Dexos2 5W-30. Valve stem seal replacement for blue smoke on startup.
High Confidence430 owner reportsLast reported by owners Feb 2026Reviewed Feb 2026
On the 2006-2016 GMC Sierra 2500HD, the Garrett variable-geometry turbocharger used on the LBZ, LMM and LML Duramax controls boost by pivoting vanes on a unison ring inside the turbine housing. Soot and carbon bake onto the ring over time and it begins to bind, so the actuator can no longer move the vanes to the commanded position. The ECM sees the mismatch and sets P003A (turbocharger position performance) and/or P2563 (turbocharger vane position sensor performance), usually together, and puts the truck in a reduced-power state. Trucks that idle a lot or run short trips soot the ring up fastest. Duramax forum and Diesel Place threads on these two codes run for hundreds of pages across 2006-2016 Sierra 2500HD trucks.
Diagnose which half of the system failed before buying parts. If the vane position sensor alone is faulty it bolts to the turbo actuator and is a comparatively cheap replacement. If the vanes themselves are stuck, the turbo must come off so the unison ring, vanes and turbine housing can be cleaned and freed; badly coked units get replaced. No recall applies. Reducing extended idling and running the engine at load periodically slows re-coking.
On the 2011-2025 GMC Sierra 2500HD, the Allison 1000 (gas) and Allison 2000 (diesel) 6-speed automatic transmissions used in Sierra 2500HD/3500HD are widely regarded as extremely durable, but the Transmission Control Module (TCM) and solenoid pack do develop faults. Common issues include harsh 1-2 shifts, transmission sticking in one gear, slip codes, and the truck going into limp mode (3rd gear only). The Allison's proprietary Transynd fluid is critical — using non-approved fluid is the leading cause of premature solenoid wear. TCM software updates from GM address most calibration-related shift complaints.
Check engine light with transmission codes (P0700, P0730, P0751)
Transmission not shifting above 3rd gear under load
How to Fix
TCM software update at dealer. Allison Transynd fluid service (drain/fill every 30k miles, full exchange every 60k). Solenoid pack replacement (Allison 29539579). TCM replacement if software update fails. Always use genuine Allison Transynd TES-295 or Mobil Delvac 1 ATF — not GM DEXRON products.
High Confidence510 owner reportsLast reported by owners Feb 2026Reviewed Feb 2026
On the 2014-2018 GMC Sierra 2500HD, on gasoline-engine 2014-2018 Sierra 2500HD trucks the belt- and cam-driven vacuum pump that supplies the brake booster loses output as debris and oil sludge accumulate on its internal filter screen. As vacuum falls the booster provides progressively less assist, so pedal effort rises and stopping distance grows - most noticeable at low speed and on the first stop after startup. GM recalled roughly 3.46 million trucks and SUVs under NHTSA campaign 19V645000 in October 2019 after linking the defect to 113 crashes and 13 injuries. Note this is a gas-engine brake-assist defect and is unrelated to the Duramax's separate vacuum arrangement.
Common Symptoms
Hard brake pedal requiring high effort
Longer stopping distances, especially at low speed
Brake warning or service brake assist message
Pedal firmness varying between stops
How to Fix
Free recall remedy under 19V645000: the dealer reprograms the Electronic Brake Control Module so the ABS system supplements braking when vacuum is low. That software remedy does not restore the pump itself - if the pedal is already hard, the vacuum pump usually needs to be replaced as a separate paid repair. Check the VIN on nhtsa.gov/recalls; the remedy is still available at no charge.
On the 2011-2015 GMC Sierra 2500HD, separate from the small-car ignition switch scandal, GM recalled full-size trucks including the Sierra 2500HD for an ignition lock actuator that binds inside the lock housing. The key becomes hard to turn, can stick in the START position, and can then snap back to ACCESSORY while the vehicle is being driven - shutting off the engine and with it the power steering and power brake assist, and disabling the air bags. NHTSA campaign 14V827000 covers the earlier population including 2012 Sierra 2500 trucks, and 15V640000 covers the later group including 2015 models.
Common Symptoms
Key difficult to turn or sticking in the ignition
Ignition sticks in START then falls back to ACCESSORY
Engine shutting off while driving
Loss of power steering and brake assist after shutdown
Air bag warning light
How to Fix
Free recall remedy: the dealer inspects the ignition lock housing and replaces the lock actuator/housing where required. Until the repair is done, drive with nothing else on the key ring so the added weight cannot help pull the cylinder out of RUN. Check the VIN at nhtsa.gov/recalls - both campaigns are still open on unrepaired trucks.
On the 2011-2016 GMC Sierra 2500HD 6.6L Duramax V8 (RPO LML), the 2011-2016 6.6L Duramax RPO LML added selective catalytic reduction, and the aftertreatment hardware is the engine's most frequent expense. The DEF tank heater and level/quality sender assembly fails often, the DEF (reductant) injector crystallizes and clogs, and pre-2015 NOx sensors drift out of calibration and report false "DEF quality poor" faults. Because these are emissions-critical, the truck gives a countdown of remaining miles and then enforces a hard speed limit - typically 65 mph then 4 mph - regardless of whether the DEF fluid is actually bad. Owners on duramaxforum.com and silveradosierra.com report P20EE, P249D and P22FE as the recurring set. This is LML-specific; the LMM has no DEF system.
"DEF Quality Poor" or "Service Emission System" message with mileage countdown
Speed limited to 65 mph, then severe limp mode
Check engine light
Reduced power
DEF gauge reading incorrectly
How to Fix
Read the specific fault before replacing anything - a NOx sensor fault, a heater circuit fault and an injector fault all produce the same dash warning. Clean or replace the DEF injector if it is crystallized, replace the failed NOx sensor (there are two, upstream and downstream, and they are not interchangeable), or replace the DEF tank heater/sender assembly. There is no general recall for these parts; some repairs fall under the federal 8-year/80,000-mile emissions warranty, which is worth checking before paying. Use only fresh, in-date DEF and keep the tank from sitting part-full for long periods.
On the 2011-2023 GMC Sierra 2500HD, sierra 2500HD 4WD trucks use a front axle disconnect system with an electronic actuator and Integrated Wheel End (IWE) hubs. The actuator motor and position sensor commonly fail between 80,000-120,000 miles, causing the 4WD system to not engage, to partially engage (binding and vibration), or to throw a 4WD Service warning. Heavy-duty truck use — particularly towing and off-road — accelerates actuator wear. The IWE hubs (vacuum-operated on some variants, electric on others) also fail, causing a grinding or clicking noise from the front axle in 2WD mode when the hub disengages incompletely.
Grinding or clicking from front axle at highway speed in 2WD
Vibration when 4WD engaged on dry pavement
4WD indicator light flashing or not illuminating
Binding or tight steering in 4WD
How to Fix
Replace front axle actuator motor (GM 84243791 or Dorman 600-140). Inspect IWE hubs for wear/failure. Change front differential and transfer case fluid simultaneously. Diagnose with scan tool to confirm actuator vs. TCCM fault. Some owners replace vacuum lines on IWE systems with updated silicone lines to prevent cracking.
What you need to diagnose it
The repair instructions explicitly call for reading stored codes. Use a scanner that can read the named code families before choosing a repair.The recommended scanner supports these code families; confirm your exact year, model and module coverage before buying.
As an Amazon Associate, we earn from qualifying purchases. Prices are approximate and may vary.
Reading and clearing the code is DIY work. Module replacement or reprogramming is not — most modules are VIN-programmed, so a new one does nothing until a shop codes it to your car. Check for an open recall or service bulletin before buying anything.
High Confidence380 owner reportsLast reported by owners Feb 2026Reviewed Feb 2026
On the 2001-2014 GMC Sierra 2500HD, the electric-shift NV246/NV263 transfer case on Sierra 2500HD trucks is positioned by an encoder motor mounted to the case, with a sensor ring inside it reporting shaft position back to the Transfer Case Control Module. Moisture and road salt corrode the encoder motor and its sensor ring, and the dash selector switch itself develops open contacts. When the TCCM loses a valid position signal it illuminates "Service 4WD" and refuses to shift. The classic pattern owners describe is a truck that will still drop into 4LO but will not engage 4HI, because the module can drive the case to its travel extremes but cannot stop it at the intermediate position. C0327 is the code that identifies it.
"Service 4WD" message on the driver information center
4HI will not engage but 4LO will
No response at all from the 4WD selector buttons
Buttons flashing continuously
Grinding or clunking when attempting to shift the case
How to Fix
Read the TCCM codes before replacing anything - C0327 points at the encoder motor or its sensor ring, while a dead switch produces no motor sound at all. On many trucks only the encoder sensor ring inside the motor needs replacing, which is far cheaper than the complete motor. A failing encoder motor can short and damage the TCCM, so both are sometimes needed; a replacement TCCM must be programmed to the vehicle's 4WD configuration with a dealer-level scan tool. No recall applies.
On the 2001-2014 GMC Sierra 2500HD, sierra 2500HD trucks with the 8.1L Vortec big block and the 6.0L Vortec V8 shed exhaust manifold bolts, particularly at the front and rear ends of the manifold where thermal growth is greatest. The steel bolt corrodes and seizes in the aluminum-adjacent cylinder head interface and stretches through repeated heat cycles until the head snaps off, leaving the manifold loose against the head. The result is a cold-start exhaust tick that quiets as the metal expands, plus unmetered air entering the exhaust ahead of the oxygen sensors, which drives lean codes. This is a gasoline-engine failure - it does not apply to the Duramax.
Ticking or puffing noise on cold start that fades as the engine warms
Exhaust smell in the cabin
Check engine light with lean codes
Reduced fuel economy
Soot marks at the manifold-to-head joint
How to Fix
Broken bolts must be extracted; the remaining stubs are usually drilled and tapped with the head still on the engine, and the manifold gaskets replaced. ARP or similar studs are the standard replacement because they do not stretch the way the factory bolts do. Where a bolt hole is unrecoverable, GM-style manifold clamp brackets bolt into unused holes in the head and clamp the manifold down. Do not simply add gasket sealer to a loose manifold - it will not hold.
What is the 2011-2016 GMC Sierra 2500HD LML Duramax EGR Cooler and EGR Valve Failure?
The LML Duramax EGR (exhaust gas recirculation) cooler is prone to coolant leaks internally, allowing coolant to enter the intake manifold and combustion chambers. Coolant in the intake causes white smoke, rough running, and potential hydrolocking of cylinders. The EGR valve also… Repairs typically run $1,200-$3,500. Severity: high.
What is the 2011-2025 GMC Sierra 2500HD Allison 1000/2000 Transmission TCM Failure and Harsh Shifting?
The Allison 1000 (gas) and Allison 2000 (diesel) 6-speed automatic transmissions used in Sierra 2500HD/3500HD are widely regarded as extremely durable, but the Transmission Control Module (TCM) and solenoid pack do develop faults. Common issues include harsh 1-2 shifts, transmiss… Repairs typically run $300-$4,500. Severity: high.
What is the 2014-2020 GMC Sierra 2500HD 6.0L V8 Excessive Oil Consumption and AFM Lifter Wear?
The 6.0L L96 V8 gasoline engine in Sierra 2500HD (non-diesel) suffers from Active Fuel Management (AFM) lifter failures similar to the 5.3L in Sierra 1500 — though less frequently due to the higher displacement. More commonly, 6.0L engines exhibit excessive oil consumption (1 qt… Repairs typically run $400-$7,000. Severity: high.
What is the 2014-2018 GMC Sierra 2500HD Engine Vacuum Pump Output Decay Reducing Power Brake Assist (Recall 19V645000)?
On gasoline-engine 2014-2018 Sierra 2500HD trucks the belt- and cam-driven vacuum pump that supplies the brake booster loses output as debris and oil sludge accumulate on its internal filter screen. As vacuum falls the booster provides progressively less assist, so pedal effort r… Repairs typically run $0-$700. Severity: high.
What is the 2011-2015 GMC Sierra 2500HD Ignition Lock Actuator Binding, Key Sticking and Unintended Rotation Out of RUN (Recalls 14V827000 / 15V640000)?
Separate from the small-car ignition switch scandal, GM recalled full-size trucks including the Sierra 2500HD for an ignition lock actuator that binds inside the lock housing. The key becomes hard to turn, can stick in the START position, and can then snap back to ACCESSORY while… Repairs typically run $0-$0. Severity: high.
What is the 2011-2016 GMC Sierra 2500HD LML DEF Tank Heater, DEF Injector and NOx Sensor Failures Triggering Speed-Limited Limp Mode?
The 2011-2016 6.6L Duramax RPO LML added selective catalytic reduction, and the aftertreatment hardware is the engine's most frequent expense. The DEF tank heater and level/quality sender assembly fails often, the DEF (reductant) injector crystallizes and clogs, and pre-2015 NOx… Repairs typically run $400-$2,500. Severity: high.
What is the 2011-2023 GMC Sierra 2500HD Front Axle Disconnect Actuator and IWE Hub Failure (4WD Engagement Issues)?
Sierra 2500HD 4WD trucks use a front axle disconnect system with an electronic actuator and Integrated Wheel End (IWE) hubs. The actuator motor and position sensor commonly fail between 80,000-120,000 miles, causing the 4WD system to not engage, to partially engage (binding and v… Repairs typically run $350-$1,800. Severity: medium.
What is the 2006-2016 GMC Sierra 2500HD Variable-Geometry Turbo Unison Ring Seizing and Vane Position Sensor Failure (P003A / P2563)?
The Garrett variable-geometry turbocharger used on the LBZ, LMM and LML Duramax controls boost by pivoting vanes on a unison ring inside the turbine housing. Soot and carbon bake onto the ring over time and it begins to bind, so the actuator can no longer move the vanes to the co… Repairs typically run $250-$2,800. Severity: medium.
What is the 2001-2014 GMC Sierra 2500HD Transfer Case Encoder Motor and Selector Switch Failure Causing "Service 4WD" and Loss of 4HI?
The electric-shift NV246/NV263 transfer case on Sierra 2500HD trucks is positioned by an encoder motor mounted to the case, with a sensor ring inside it reporting shaft position back to the Transfer Case Control Module. Moisture and road salt corrode the encoder motor and its sen… Repairs typically run $250-$900. Severity: medium.
What is the 2001-2014 GMC Sierra 2500HD Exhaust Manifold Bolt Breakage and Manifold-to-Head Leak on Gasoline V8s?
Sierra 2500HD trucks with the 8.1L Vortec big block and the 6.0L Vortec V8 shed exhaust manifold bolts, particularly at the front and rear ends of the manifold where thermal growth is greatest. The steel bolt corrodes and seizes in the aluminum-adjacent cylinder head interface an… Repairs typically run $400-$1,600. Severity: medium.
