2015 Ford Fiesta Problems: 23 Known Issues

On the 2011-2019 Ford Fiesta 1.6L Ti-VCT, the Ford Fiesta equipped with the DPS6 PowerShift dual-clutch automatic transmission is one of the most complained-about vehicles in recent history. The dry dual-clutch design causes severe shuddering, jerking, hesitation, and complete loss of power during acceleration. The clutch plates overheat and wear prematurely, often before 50,000 miles. The Transmission Control Module (TCM) software frequently fails to adapt properly, causing delayed shifts, harsh engagement, and rollback on hills. Ford faced a class-action lawsuit involving nearly 1.5 million vehicles and a federal settlement was reached.

On the 2011-2015 Ford Fiesta 1.6L Ti-VCT Duratec, separate from the clutch-pack shudder already documented: the DPS6 PowerShift's Transmission Control Module, mounted on the transmission and exposed to heat, fails electrically. The car suddenly loses drive while moving, will not start, drops into limp mode, or the cluster throws a transmission fault with stored U0101 (Lost Communication with TCM). Ford acknowledged it with Customer Satisfaction Program 14M02, extending TCM coverage on 2011-2015 Fiestas to 10 years / 150,000 miles. Because a failed TCM cannot be reflashed, replacements also require a Ford reprogram, and parts shortages in 2019-2021 left owners waiting weeks.

On the 2011-2019 Ford Fiesta, manual-transmission Fiestas (5-speed B5/IB5; 6-speed B6 on the ST) commonly develop clutch judder, a soft/sinking pedal, and inability to select gears when the concentric slave/release cylinder or clutch master cylinder fails. Owners report the clutch going to the floor when stopped and gears becoming impossible to select, sometimes temporarily restored by restarting. Because the slave cylinder is inside the bellhousing, replacement requires removing the transaxle, so labor is significant. Contributing factors include worn or dislodged master-cylinder internals, contaminated hydraulic fluid, and normal clutch wear producing judder on take-up.

On the 2012-2017 Ford Fiesta 1.0L EcoBoost I3 turbo (M1JE / M1JH / SFJB), the 1.0L EcoBoost uses a brittle nylon degas/coolant return hose running from the top of the expansion tank to the engine. Over thousands of heat cycles the nylon becomes brittle and cracks or snaps, often at highway speed. Because the engine has a very small coolant capacity and high thermal load, a burst hose causes total coolant loss in seconds; the aluminum cylinder head then overheats almost instantly, warps, and blows the head gasket — the failure mode owners nickname 'EcoBoom.' In March 2015 Ford issued a UK Field Service Action to replace the coolant pipe on about 44,682 1.0L cars built between October 2011 and October 2013, and in 2018 Ford UK agreed to pay 100% of dealer repair costs for 1.0L overheating failures linked to the fault. Owners are advised to check whether the hose from the expansion tank is hard black plastic (original, at-risk) or flexible rubber (updated).

On the 2014-2015 Ford Fiesta 1.6L EcoBoost GTDI, distinct from the 1.0L EcoBoost degas-hose failure: the 1.6L EcoBoost in the 2014-2015 Fiesta ST has cylinder-head coolant passages that develop localized hot spots. If coolant is lost (the ST has no low-coolant warning from the factory), the head overheats and can crack, leaking oil onto the hot turbo/exhaust and starting an engine-bay fire. Ford recalled the 2014-2015 Fiesta ST alongside other 1.6L EcoBoost vehicles under 17S09 / NHTSA 17V209. Owners on fiestastforum report coolant loss with no leak found, temperature spikes and, in the worst cases, cracked heads.

On the 2011-2019 Ford Fiesta, the Ford Fiesta is prone to blend door actuator failure, which controls the mix of hot and cold air in the HVAC system. When the actuator motor or its plastic gears fail, the system gets stuck blowing only hot air or only cold air regardless of temperature settings. A characteristic clicking or tapping sound from behind the dashboard is the telltale sign of a failing actuator. The plastic gears inside the actuator are undersized and strip easily, especially in extreme temperatures.

On the 2013-2019 Ford Fiesta 1.0L EcoBoost 3-cylinder turbo (belt-in-oil), the 1.0L EcoBoost uses a 'wet' timing belt that runs submerged in engine oil. When oil is old, over-extended, or not to Ford's WSS-M2C948-B spec, the belt's rubber breaks down and delaminates ('pilling'). Shed fragments migrate through the sump and clog the oil pump pickup screen, causing loss of oil pressure and catastrophic engine failure. NHTSA opened an investigation after dozens of complaints of low oil pressure followed by power loss on 1.0L EcoBoost vehicles. Ford originally specified a 150,000-mile belt interval, but with failures averaging about 70,000 miles Ford cut it to 100,000 miles or 6 years, whichever comes first. Failure can also destroy the belt-driven oil pump and cause the crank pulley to shed the belt.

On the 2011-2019 Ford Fiesta, the drive-by-wire electronic throttle body (ETB) develops an internal electronic/motor fault (not just dirt) that causes the powertrain control module to command reduced power. The car drops into limp mode with a wrench/powertrain-malfunction light, often storing throttle-position or actuator-control codes. Because the failure is internal to the unit, cleaning does not fix it. This is a recognized Ford-family ETB problem shared with Focus, Escape, Fusion and Transit Connect, and is reported by Fiesta owners including on the 1.6L engines.

On the 2011-2015 Ford Fiesta, ford recalled over 2 million vehicles including 2011-2015 Fiesta sedans and hatchbacks because of faulty door latches that can break internally. When the latch fails, the door may not close securely or may open unexpectedly while the vehicle is moving. The problem is caused by a pawl spring tab that can fracture inside the latch mechanism, particularly in warm climate states where heat accelerates material degradation. Ford issued multiple recalls (20S15, 20S30) to address this safety hazard.

On the 2011-2019 Ford Fiesta All engines, fiestas commonly get wet passenger (and sometimes driver) footwell carpets from rainwater entering via the scuttle panel at the base of the windscreen. Leaves and debris block the scuttle drain, or the scuttle-to-windscreen seal fails, letting water pool and overflow into the cabin heater/pollen-filter housing and down into the footwell. The soaked carpet can cause musty smells, foggy windows, and electrical corrosion in floor connectors. It affects multiple generations and is a top owner complaint.

On the 2014-2015 Ford Fiesta 1.6L Ti-VCT, improper nickel plating of internal components in the Bosch in-tank fuel pump can cause the pump to fail, letting the engine stall without warning and increasing crash risk. Ford issued NHTSA recall 15V005000 covering certain 2014-2015 Fiesta (and related Escape, Edge, Focus, Transit Connect and Lincoln MKC) vehicles built spring 2014; the recall was first announced January 2015 and later expanded April 30, 2015. Owners report intermittent no-start and stalling. Outside the recall window, general in-tank pump wear produces similar hot-restart/low-pressure symptoms.

On the 2011-2019 Ford Fiesta, the EVAP canister purge valve sticks open, causing difficulty fueling (pump nozzle keeps clicking off), rough idle, and check engine light. Very common on the 1.6L engine.

On the 2011-2019 Ford Fiesta All engines, fiestas can display 'Power Steering Assist Fault — Service Required' and lose electric power-steering assist, sometimes intermittently while driving. Root causes include torque-sensor faults and intermittent electrical connections in the steering column/gear that stop the control module from commanding the assist motor. When assist drops out the wheel becomes very heavy (manual mode), and some owners report the wheel jerking or pulling; Ford's broader EPS defects have driven multiple recalls and legal actions across its lineup. This is a safety-relevant electrical/steering failure.

On the 2008-2019 Ford Fiesta, the suspension coil springs fracture, typically near the bottom coil, often triggered by corrosion at the spring seat combined with road-input stress from speed bumps and rough surfaces. This is a very frequently reported Fiesta failure — front springs are most commonly cited but rears also fail. A snapped spring can cut into the tire and causes uneven ride height, a lean to one side, clunking/creaking, and unstable handling. Corroded spring isolators (rubber seats) commonly fail alongside the spring.

On the 2009-2019 Ford Fiesta, rear wheel bearings on the Mk7-generation twist-beam Fiesta (including the ST) wear prematurely, producing a hum or drone that rises with road speed and changes pitch when the car is loaded in a corner. Ford Owners Club, FiestaSTOC and fiestastforum all carry multiple threads, with ST owners reporting replacement as early as 47k miles. The bearing is pressed into the hub rather than sold as a bolt-on unit on the ST, and the noise is commonly misdiagnosed as tire noise until it becomes loud.

On the 2011-2019 Ford Fiesta All engines, fiestas (2008–2019, including ST) frequently develop knocking, clunking, or scrubbing noises from the rear suspension over bumps. Common causes are worn rear shock-absorber top mounts, deteriorated damper eye/lower-mount bushings, and torn rubber that lets the shock move in its mount. Owners also find rattling heat shields and, occasionally, a broken coil-spring fragment knocking in the lower mount. It is a wear-and-tear NVH issue rather than a catastrophic failure, but it is one of the most-searched Fiesta annoyances.

On the 2009-2017 Ford Fiesta, on Mk7 and Mk7.5 hatchbacks (2009-2017) the exterior tailgate release button sits directly below the rear wiper spindle. Water and grit run down through the wiper hole, pool around the switch, and corrode its contacts. The result is a hatch that will not open from outside (owners crawl through from the rear seat), or a 'boot open' warning and interior light that stay on because the latch microswitch signals the body control module incorrectly. Ford released a modified switch with better sealing; Ford Owners Club and TalkFord threads document it across many cars.

On the 2011-2019 Ford Fiesta All engines, fiesta SYNC/MyFord Touch and SYNC 3 systems commonly freeze, randomly reboot, drop Bluetooth pairing, and lose Apple CarPlay connectivity. Many failures are software 'handshake' hangs, but a subset are hardware failures of the Accessory Protocol Interface Module (APIM), which can enter a 'zombie' state where it draws power but the UI is frozen and soft resets do nothing. Symptoms include black screens, disappearing menus, unresponsive buttons, and USB ports that stop charging. A physical APIM fuse-pull/hard reboot resolves most connectivity hangs; persistent freezing points to APIM hardware or corrupted firmware.

On the 2011-2019 Ford Fiesta, diesel Fiestas frequently suffer diesel particulate filter (DPF) blockage and incomplete/failed regeneration, especially on cars used mainly for short, low-speed journeys that never reach regeneration temperature. Soot accumulates, the DPF warning light appears, and the car may enter limp mode or dump excess fuel into the oil during failed active regens (raising oil level and diluting it). Underlying triggers are often other faults — a leaking/faulty injector, stuck EGR, blocked intake, or failed DPF differential-pressure/EGT sensor — so the blocked DPF is frequently a symptom rather than the root cause.

On the 2009-2019 Ford Fiesta, fiestas fitted with rear discs (ST, Titanium and higher EU trims) suffer seized rear caliper slide pins and stuck parking-brake actuating levers. Road salt corrodes the pins and the lever pivot, so the pad drags constantly: rapid inner-pad wear, a hot wheel and burning smell after driving, pulling under braking, and in the UK a frequent MOT failure for handbrake imbalance. FiestaSTOC and TalkFord threads describe repeated recurrences when only the pads were changed. Base models with rear drums are not affected in the same way, though their handbrake cables can also seize.

On the 2014-2019 Ford Fiesta 1.6L EcoBoost (ST), the Fiesta ST's soft OEM rear motor mount (RMM / 'dogbone') bushing cannot withstand the 1.6L EcoBoost's torque and the high heat at its location, so the rubber degrades and allows excessive engine movement. This produces clunking on throttle on/off, driveline shudder, and wheel hop under hard acceleration, and accelerates wear on the remaining mounts. It is one of the most-discussed Fiesta ST maintenance items; owners commonly fit a polyurethane insert or an upgraded mount to eliminate the slop.

On the 2008-2019 Ford Fiesta, the plastic-geared window motor cog and the regulator's lift cables/clips wear or break, causing the window to fall inside the door, stick partway, or move only after repeated button presses. A characteristic symptom is a clicking/chattering or grinding noise as the glass jams or slips off its carrier. Commonly affects the driver's door (highest cycle count) but occurs on all doors, and the 3-door glass is frequently cited. Distinct from a purely electrical (switch/fuse) fault — the motor often runs while the glass does not move because the cable/cog has failed.

On the 2009-2019 Ford Fiesta, on Fiestas with manual HVAC, blower speeds 1-3 run through a resistor pack in the passenger footwell while speed 4 is fed 12V directly. The resistor's thermal link burns out, leaving the fan working only on full blast. The failure is very common on Mk7/Mk7.5 cars and often recurs within months if the underlying cause — a stiff, high-current blower motor or a blocked pollen filter starving the resistor of cooling air — is not addressed. Ford Owners Club and TalkFord have many threads on it.